The specification that states there is too much window space proportionate to the square footage of the room, is about as stupid as it sounds, how many old houses exist in Mass. with large windows of the past ?
What I would want to know (and I recognize you are more frustrated by the above) what R value or what value of the exterior wall, is established with new construction. Get that on the table, then detail the rough opening and take that to a manufacturer, see what existing window models may perform or equal that rating, I would think its out there. Then it would be a matter of having custom windows/glazing built, subsequently properly installed to achieve a uniform rating.
I could not buy this for a minute without knowing the above, I worked extensively in the metal and glass industry, know commercial window assemblies inside out, usually the window performs, but its the installation that presents problems, ie; the rough opening. On the residential end, there has to be a thermally broken window, with glazing that will perform at that size, I can't see the insulated glass being too thick to create a larger air space, and increasing the window assembly to not fit into a residential rough opening, losses always occur around the rough opening, air and water infiltration, I have performed the tests in mock up laboratories, on commercial windows, know the routine. There is a lot to obtaining ratings or certifications by reference standards, A.A.M.A and you may search the link to find more information about this.
To heck with the contractor, Allan is right, they just don't want to deal with it, not too many are well versed in solving problems like this. I've heard this can't be done or that can't be done, 14 years ago, an old bow window, on the weather side of the house was deteriorated on the bottom, the sill, the bottom operating sash, needed to be re-glazed etc., contractor said it needs to be replaced this and that, can't be done ( meaning we don't want to do it)
I set up scaffolding, I removed what was rotten, I made the bottom sill myself on the sawhorses, CCA pressure treated wood, I made new bottom rails for the 2 operating sash, I called a buddy in the glass business, gave him the daylight opening (D.L.O.) of all the little windows comprising the overall unit, ordered the new insulated glass, re-glazed it, made new glazing stops, installed with new glazing compound, painted etc. it was less than a new unit installed, only mistake I made was not ordering Low E on on of the surfaces of the insulated glass, there are surfaces # 1, 2, 3, 4.
The window performs well to this day, much better than before, no real noticeable thermal loss, no need to replace and IT COULD BE DONE !!!! the repair that is. With the winter sun and all the glazing on the south side, it keeps the house very warm during the day, no matter how cold, as long as the sun is out.
I can't imagine being told what you were here, change all the window sizes, that sure is a bunch of trash !!!!
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.