My farm is out in the country 8 miles from town where I live. In town I have 14 acres.it was a real pain to move equipment back and forth. In 87 I got grandpas steel wheeled drill out of the pasture and brought it to town.
It worked real good for 14 acres. Did not have to mess with flat tires, hydraulic hoses etc just grease it and I was ready.I pulled it with my SC Case. At the farm I had a JD 8200 drill. Every fall I would spend $200 replacing rubber seed tubes, press wheels and other plastic parts.I rented the farm in 06 but kept the 14 acres in town. I took the 8200 drill to town for my 14 acres. That was a mistake. I was still buying a hundred dollars or more of parts for it each fall. Had to move the hydraulic cylinder back and forth from my disk. With grandpa's old van brunt my 14 acres was yielding 32-35 an acre. With the 8200 drill it was the same. My expense went up maintaining the 8200. I sold the 8200 and went back to the steel wheeled Van Brunt. Since 87 I have only spend $7.00 on the Van Brunt for a new spring.
I also sold my 18ft crust buster spring tooth and bought a 12ft 3pt hitch dearborn spring tooth for $25. By getting rid of the 8200 drill and the crust buster I have six less tires to buy and less hydraulic hoses. That saves me more money.
This spring someone offered me $80 an acre so I now have my 14 acres rented. But I will kept the old equipment. it is all paid for and with steel wheels or 3pt hitches I won't have many flat/rotten tires.
For smaller acres, the OLDER equipment you can find the better off you will be.
I had a neighbor across the street that had five acres. he planted it to oats every year and baled it for hay. He told me he made enough money off his oats to pay is property taxes. his equipment was all most all Ford. 8n tractor,3pt dearborn mower,rake,plow,spring tooth,and disc. 6ft McCormick drill, and NH baler. other than the tractor he only had four tires. two on the baler and two on the drill. I'm sure if he had newer equipment he would have lost money on his 5 acres.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Good As New - by Bill Goodwin. In the summer of 1995, my father, Russ Goodwin, and I acquired the 1945 Farmall B that my grandfather used as an overseer on a farm in Waynesboro, Georgia. After my grandfather’s death in 1955, J.P. Rollins, son of the landowner, used the tractor. In the winter 1985, while in his possession the engine block cracked and was unrepairable. He had told my father
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
