Posted by Paul on September 17, 2014 at 08:56:12 from (76.77.197.114):
In Reply to: 3pt or pull type posted by young tractor on September 17, 2014 at 07:07:20:
I'm in southern mn, heavy clay.
I have a 10 shank 2" old chisel plow, my 85 hp didnt pull it very deep. Or fast.
My 140hp dualed tractor did good with it, but seemed it never did much tillage really. Little slots through the stubble.
Got a Glencoe soil saver,7 shank, has flat disks up front, 4 inch twisted shanks.
In the dry ground we had 2 years ago that was a workout for my 140 hp, but worked well. Worked the ground nice and didnt plug much. Was the tool and size I needed to get my baked dry clay shattered, opened, and working again.
I suppose a 9 shank would work most of the time on my 140hp, but the times it doesn't is when you really want to shatter the hard clay the most, and is most needed. When the soil is mellow and the chisel pulls easy, you probably could leave it in the shed!
I think you would be looking for a good 7 shank heavy or very light 9 shank chisel for your tractor, and even at that you often will be doing less than you wanted?
I only have experience with pull type, I believe they are generally better but not a deal breaker on a small 3pt unit that is a good deal wouldn't be afraid of that at all?
As I get older, I guess I want to do a better job, and be conservative with the hp I have for the big tillage. More hp, less machine has equalled a better job. When I look back at what I did with a too small tractor, going too slow and too shallow, I got poorer results for the whole year. That was not good for the tractor or my crop or my bottom line.
If you have any trash at all on the surface, even high yielding bean stubble, a chisel with more clearance will make you much much happier long after it is paid off..... But we all start somewhere. ;)
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Show Coverage: Journey to Ankeny - by Cindy Ladage. We left Illinois on the first day of July and headed north and west for Ankeny, Iowa. Minus two kids, we traveled light with only the youngest in tow. As long as a pool was at the end of our destination she was easy to please unlike the other two who have a multitude of requirements to travel with mom and dad. Amana Colonies served as a respite where we ate a family style lunch that sustained us with more food than could reasonably fit into our ample physiques. The show at Ankeny
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
