PIPE SIZE: I want the large diameter so there is enough water available at any give time. The water that recharges the well is a slow trickle. Thus the need for some sort of reserve. A standard 5" or 6" well casing works fine when there's over a 100 feet of well involved. Not so good when the well is only 8-10 feet deep. Assuming the well will freeze in the upper end. a 10 foot well is only going to have around 6 feet of water in it . If that was a 6" pipe it would only hold around 9 gallons of water. If I use a 36" pipe it will hold 300 gallons of water.
FIXING A PUMP IN THE WELL? If I put a pump in the well is will be near the bottom, under water and attached to whatever casing I use with a pitless adapter. No need to "go in well" to fix if the pump craps out. Just take 10 minutes to yank it out from the top.
LEGALITY: I don't really care. The house already has a very deep, health department well that has lousy water. As far as I am concerned - it nobody's business in government whether I opt to install an additional well that gives better water. The reason why the water is lousy now if due to the health department regs for the primary well having X amount of GPM available. In regard to bacteria - already checked it an it's fine. This well is in the edge of a pretty much pristine woods, 100 feet from the river, and in the middle of a 10 acre parcel. Very low impact area and every house in the area is on at least 10 acres. Septic leach-field is 200 feet distant. Ground horizon makeup is sand and clay for a very long way down.
SUBMERGED "PUSHER" PUMP. I am hoping to use one because I already have an extra on hand. It is also more efficient and quieter then using a Jet pump in the house. I was concerned about the lack of a torque arrestor because of prior experience with submersible pumps breaking plastic pipes from torque. Maybe if I use steel pipe connecting the pump to the pitless - it won't be an issue?
WELL POINTS? Having lived most of life in NY - I'd never seen a well point until coming to sandy Michigan. NY has so much rock and hard-pan - driving a point would of been impossible anywhere I've lived there. I'll have to read up on them but I assume it could not work in my situation. I think this setup needs a reservoir due to the slow water recharge.
QUESTIONS ABOUT ANIMALS FALLING IN THE WELL? Seems the answer ought to be obvious. A cover on the well. That being said, I had a Holstein cow break through a wood-covered dug well in NY. Won't be an issue here.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - 12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.