36F30 said: (quoted from post at 16:02:06 12/10/14)
philcaseinwpa said: (quoted from post at 11:44:44 12/10/14) I have a chance to get my driveway paved for free to my specs. This will have to support tractor traffic and some school buses and heavy trucks. What should I specify for base, thickness, reinforcement, mix, expansion joints etc. I want concrete not asphalt.
Thanks
Phil
If your getting this done for free, go pay a local engineer to give you specs. NOBODY on here knows your soil type, texture, permeability, and if your soil is expansive or not. Good concrete starts with a good base. Grade and drainage are important as well and again, no one here can see that. You have one chance to do it right make the most of it.
I'm with '36F30' the only thing I would add is to use fiber in the mix if you want strength; and it is much cheaper than rebar. Fiber is kind of a new technology in the concrete world (last 10 or 15 years or so) They clam that is is stronger than steal and it does give a lot of strength to concrete. I drove concrete trucks for over 10 years and worked with concrete for over 20 years. I found the fiber (now micro-fiber) is so inexpensive I used it in footers, grout and mortar mixes. Now if I think concrete I think fiber, but I also still use rebar and/or wire.
I would try to refrain from using any calcium because it diminishes the tinsel strength considerably. As for air entrainment I would ask the dispatcher how much to use. They will know the idiosyncrasies of the mix and the area, like water and soil pH and what they are using No. 1 or No.2 cement, and what type of cement they are using (Portland). This can change the amount of air entrainment you will need or if you need to use it at all. When your are mixing 4 1/2 oz. to 8 yards of mix a 1/2 oz. can make or break ya (don't excuse the pun). Air entrainment makes micro bubbles in the mix which expands the amount of mix but after a certain point the concrete becomes soft.
Also think of the future... are you going to bring any tracked rigs inside the shop on the slab? If you think you might I would put rail road rails (steal) in the slab where the tracks will travel. Leaving the rails slightly exposed so the tracks wont destroy the slab.
This post was edited by Fatamus at 08:37:12 12/11/14.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.