Posted by Geo-TH,In on January 20, 2015 at 13:16:43 from (104.240.206.35):
I made two energy management devices for my two generators 3500 w RV generators. I want portable generators to use at any of 12 different locations. And there is no way I want to have them within 100 ft of a house and have exhaust get inside. I choose to go with RV generators because I want to have 30 amps coming out of one place. You can't say that about larger generators. Most I've seen are only 20 amps, 120v out. I'm sure there may be larger generators for RV's that have larger outputs. But I'm cheap and happy with a 3500w one.
So I wanted to use a small quieter, more economical RV generator. I also wanted to use my generator to be portable so I can power hedge trimmers, small water pump, 4 hp chainsaw which requires 70 amps when it first starts, power up a 3/4 hp well pump, refrigerator and small appliances like hot plate, coffee pot, toaster.
So here is a brief description of how it works for house back up power. When the well comes on, everything else is turned off. When well is off the small appliances gets power, then up to 10 minutes the refrigerator gets powered up. This way my largest load, the well, gets the generators full attention. It's no big deal for me to put 2 cords through the kitchen window and rest them on counter. No big deal to put a wire through basement window and power pump.
When when I use the 4 hp chainsaw, I have a large diode placed in series with saw for 1 second. The saw is only getting half waves, half the current and 1/4 the power. I use the diode to get the armature going, produce a reverse emf, limit starting current to 35 amps. One second later, the saw gets full voltage and uses normal current of 15 amps. This prevents the generator from shaking for about 3 seconds when I start the saw.
The bigger box is my first generation. The smaller box is the same, just more compact.
Everything except for the 1 second timer is old school parts used 50 year old furnaces and AC. Most of the parts I already had sitting on the shelf.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Grain Threshing in the Early 40's - by Jerry D. Coleman. How many of you can sit there and say that you have plowed with a mule? Well I would say not many, but maybe a few. This story is about the day my Grandfather Brown (true name) decided along with my parents to purchase a new Ford tractor. It wasn't really new except to us. The year was about 1967 and my father found a good used Ford 601 tractor to use on the farm instead of "Bob", our old mule. Now my grandfather had had this mule since the mid 40's and he was getting some age on him. S
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.