Posted by Bill VA on May 21, 2015 at 06:31:35 from (76.3.243.86):
Adding a little capacity to the hay storage and a few carport (for lack of a better word) questions.
I've got a 20w x 30l x 10h ft dome shaped building frame I am going to put up to store some hay and maybe an implement. The shelter was designed for use with a vinyl type cover, not unlike a large tarp.
On each side of this thing is a tube running the length of it, with holes every 3 or 4 ft for anchors - so I'm considering my options.
One of my thoughts was to dig post holes, fill with concrete and use a lag bolt to secure the frame at each anchor point. The lag bolt is threaded and if I ever needed to move the building, I could unscrew it from the bolts. I would put the lag bolts in when I pour the concrete.
The other option is to cut some rebar, weld a cap on it and drive them into the ground holding the shelter in place.
Depth: I can see a rebar anchor being 24 or more inches. If I use a post hole filled with concrete, the lag bolt could only go down about 12 inches and the question is - how deep (if at all) should the post hole/concrete go beyond the lag bolt? Somehow I think that even with a shallow concrete fill, the vinyl or whatever straps I'm using to hold it down would give way before the frame with cover would fly away in a hard wind storm?
BTW - the shelter didn't come with a vinyl cover, so I ordered a used bill board sign to cover this thing. Haven't unpacked it yet, but if it says "Mail Pouch Tobacco" on it, I'm turning that part out..... LOL!
Any tips, tricks and advice for anchoring this shelter are much appreciated.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - On the Road with Dave Gohl: Auction Musings - by Dave Gohl. I was thinking the other day about all the auctions I've been to in the last few years. There've been many. Some have been very good, some have been well, disappointing to say the least. But no matter how good or bad auctions may be, we always seem to stay until the item we've come for or are interested in is on the block. I've been to some auctions near and far. I think the furthest has been the Two Cylinder 7 in the Amana Colonies last year. Lots of stuff, lots of people. I've also atten
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
