Posted by Rick Kr on November 01, 2015 at 04:16:39 from (198.105.227.176):
In Reply to: Dozer question posted by notjustair on October 31, 2015 at 19:51:00:
I would definitely look at renting. Unless you can really justify A LOT of work, it doesn't make sense to buy. This is coming from a guy that just sold my JD350B in December. I owned it for 5 years and I did a ton of work. The last 1 1/2 years it mostly sat. No sense having an expense piece sitting around, so I got my money back. Of course, the week after I sold it, I "saw" four of five dozer projects that needed to be done. I plan on renting one for the weekend next summer to knock out all my projects.
Over those five years, I only put 80 hours on the dozer. Really that's not a lot. A new dozer I would think would cut that time in 1/3. As you can see in the pics 3-4 of those hours were the wife driving around in the snow when I first picked it up.
You will spend a ton of time looking for one, truly inspecting the undercarriage, trucking, fluid checks/changes when you get it home. And the list goes on. I have been on a newer D4 and D5 Cat. There is no comparison to an older dozer.
In my area of mid Michigan. I can have a NEW JD450 dozer dropped off at the house for $450 a day or $1300 for the week. It will run circles around older equipment. And it if it pukes out, you pick up the phone. You wont do that with a late 60s dozer.
Just my opinion. Good luck. And if you buy definitely post pics. I attached a pic. I miss the little guy, but just didn't need it anymore. Full 6 way hydraulic blade and reverser. No clutching. Great little machine.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Timing Your Magneto Ignition Tractor - by Chris Pratt. If you have done major engine work or restored your tractor, chances are you removed the magneto and spark plug wires and eventually reached the point where you had to put it all back together and make it run. On our first cosmetic restoration, not having a manual, we carefully marked the wires, taped the magneto in the position it came off, and were careful not to turn the engine over while we had these components off. We thought we could get by with this since the engine ran perfectly and would not need any internal work. After the cleanup and painting was done, we began reassembly and finally came to t
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.