Posted by rbhuntn on January 27, 2016 at 15:06:12 from (64.235.31.6):
In Reply to: Ford 1900 reliability posted by dziadzu on January 27, 2016 at 14:06:38:
Quoting Removed, click Modern View to see
Can't speak to the 1900. I did own its little brother a few years back the Ford 1210. These are made in Japan by Shibaura. Mine was a tough little tractor and trust me I asked it to a lot more than it was rated for and it never let me down. Kind of wish I had held on to that one.
They can be a bit of a pain to find parts for depending on what breaks but most can be had even though the parts may have to be shipped from Japan. The local New Holland dealer had access to everything I ever needed.
One thing that I will say about this series of tractors is that they had a tendency to plug up the mufflers especially the one that ran horizontal with the hood. You could always tell they were getting plugged when engine started to run a bit sluggish and seemed to smoke a bit.
I was always able to get mine to clean out by tapping on the muffler with a hammer handle with some medium tapping for a few minutes with the engine running.
One thing that I would look for during a test drive is the diff lock. These units did not like to turn with the diff engaged. If someone has used the brakes to turn the tractor with the diff lock engaged they can break things in the rear diff. The diff lock would not always dis-engage when driving forward. I often had to back mine up to get it to unlock.
To test put it up against a tree and lock it in to ensure to both rear wheels spin. If the do then should be good to go. After the test make sure you lift up on the diff lock then back up about 6-10 feet and it should unlock.
As to your question about raking and light cultivating. That would depend on the rake and plow. If you are going to use a 3 point tiller you will want stay around the 48 to 52 inch at a max and the hydro trans version works better with the tiller as you can go really slow. Not sure of the geared version will be a slow enough ground speed for a 3 point pto driven tiller.
If you find a good one they are pretty darn good little tractors. Just my thoughts.
In the Western Central Missouri area these are running from about $4,500 to $6,500 for the 2WD no loader. If 4WD average is about $5,500 to $7,000. Add 1K for loader. Again this in my area.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - When Push Comes to Shove - by Dave Patterson. When I was a “kid” (still am to a deree) about two I guess, my parents couldn’t find me one day. They were horrified (we lived by the railroad), my mother thought the worst: "He’s been run over by a train, he’s gone forever!" Where did they find me? Perched up on the seat of the tractor. I’d probably plowed about 3000 acres (in my head anyway) by the time they found me. This is where my love for tractors started and has only gotten worse in my tender 50 yrs on this “green planet”. I’m par
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
