The trusses in this barn were never properly braced as I recall. There were however a lot of perlins, and we did both, braced it per the details on the truss drawing, and installed perlins every 19" if I recall my spacer length. I made up spacers to set these to align with existing ones.
Surprisingly, the 2nd winter after this was completed, the intact section survived a close call. It had a sag in it and needed work. I did reinforce those trusses, made up plywood splice plates for the joints at the webs and the chords. The metal splice plates were failing. We had snowfall in the winter of '10-'11 that was heavy, that roof wanted to collapse and it was sounding like it would. We cleared it in time, and I did have to shore up a post that was failing.
4'centers on trusses are a real pain when trying to work with the gap and its a hole that you will easily fall through. Every perlin was a struggle to set, full thickness actual rough cut lumber, likely green and froze = heavy!
There is a lot of work in repairs like this, same with a new building, but we were able to build it back so it was whole again, that was late '09 and at some point this barn will need work again, as it does not have PT posts and they are in the ground. Its not my place, I just did the work for my father, he never listens to reason, went with some local species that the sawmill had, actual, and its built with nominal, so it did not fit in between the skirt beams the trusses set on. I had to haul that hemlock, green to a guys house 40 miles away to rip them down on 2 sides, was laid up in bed the day before with a back problem. Sometimes life really makes you wonder why a person even bothers with things such as this and it seems the contractors that walked from this posters job, trying to push a new building may be smarter than we think LOL !!!
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Talk of the Town: How to Remove a Broken Bolt - by Staff. Another neat discussion from the Tractor Talk Discussion Forum. The discussion started out with the following post: "I have an aluminum steering gear housing with a bolt broken off in it. The bolt is about a 3/8" x 1 1/2" bolt. I've already drilled the center of the bolt out with about 7/64" drill bit the entire length of the bolt. Only one end of the bolt is visible. I tried to use an easy out but it wasn't budging and I didn't want t
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
