Posted by carpetfarmer on July 13, 2016 at 06:56:34 from (165.201.76.84):
Reading Dustyah's post on the Case forum about Too Much Weight got me thinking about my own ongoing project. I know tractors have a maximum weight rating, but what exactly does this entail? A tractor can be too heavy in regards to what (field work, traction, hp-weight ratio...)?
What problems are associated with being too heavy? Of course, short of way overdoing it and blowing out front hubs and spindles, snapping axles, etc.
I'm sure it depends greatly depending on the application, but what is the fudge factor with the specified max weight?
According to tractordata my Case 1190 is listed as shipping at 4620 lb and having a max weight capacity of 7000 lb. I won't be doing any "heavy" traction work when fully loaded, but in the winter months by my calculations it will be flirting with that 7000 lb mark. When pushing snow there will be some slippage and some weight will be lost on the front end because the plow will be sitting on the ground when plowing, so it shouldn't be an issue but like I said, it will be flirting with that 7000 lb max weight capacity when the plow is up.
Tractor - 4620 lbs Front Weights - 3x 79 lb = 240 lb Wheel Weights - Unknown Snow Plow - 600 lbs (as I recall from talking to the manufacturer) Ballast Box - iMatch Ballast Box w/ Sand = 616 lb Steel Plate - 580 lb Me - 200 lb
Total Weight (short wheel weights) - 6860 lb give or take 100 lb for guesstimation.
P.S. - Does anyone know what those rear wheel weights might weigh or what they came off of? Cast into them is - BW401A D22T
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - A Lifetime of Farm Machinery - by Joe Michaels. I am a mechanical engineer by profession, specializing in powerplant work. I worked as a machinist and engine erector, with time spent overseas. I have always had a love for machinery, and an appreciation for farming and farm machinery. I was born and raised in Brooklyn, New York. Not a place one would associate with farms or farm machinery. I credit my parents for instilling a lot of good values, a respect for learning, a knowledge of various skills and a little knowledge of farming in me, amo
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.