Well you guys are a breath of fresh air (sarcasm). This is why I asked. I have another thought posted at the end with more pictures. And yes, the front bumper is out of whack on this loader, it is over 50 yrs old. After reading this, please let me know your thoughts on my additional idea listed at the end and if Centash and Janicholson's idea is still a better/easier one. If so, how do you suggest strapping the new/extended straddle?
It seems the best idea so far is Centash and Janicholson's to extend the saddle upwards and STRAP to the loader frame. On the non-reservoir side, I assume I can weld to the frame?
Centash/Janicholson.......I have noted your idea to extend the current straddle upwards and STRAP to the reservoir. What type of STRAP do you recommend? Any others have input on this? Also, I cannot extend rear of loader frame outwards, I'm already maxed.
JD......I have thought about fabricating the front mounting so the frame sits a little wider, which would give me clearance on tie rods and also give me more room for the front hood and bonnett, which is going to be very tight. I wasn't sure if this would work though because I would have to put pressure on the frame to widen it which means it is not its natural stance. Also it seemed to be more difficult than my other idea (which has now been an afterthought).
Check Break.........I'm not sure I understand your question. I did move the cylinder to the outside on both top and bottom but that seemed way too "Wonky". That's why I tried to keep at least one end in its original straddle.
Another idea I had. Note this idea would require me to have a new hose made for each side, which is why I went the other route. Not a big deal but just an additional cost. In the first picture, what if I extended the bracket at top of cylinder and put the cylinder end where I have marked in Green? This will give me clearance on my tie rods well. Note: After typing this whole thing out, I like Centash/Janicholson's idea better as long as I can get it strapped good.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Product Review: Black Tire Paint - by Staff. I have been fortunate in that two of my tractors have had rear tires that were in great shape when I bought the tractor. My model "H" even had the old style fronts with plenty of tread. My "L" fronts were mismatched Sears Guardsman snow tires, which I promptly tossed. Well, although these tires were in good shape as far as tread was concerned, they looked real sad. All were flat, but new tubes fixed that. In addition to years and years of scuffing and fading, they had paint splattered on
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
