Posted by js305 on January 02, 2017 at 06:47:12 from (70.195.198.253):
In Reply to: Re: Electrical Safety posted by K Effective on January 02, 2017 at 05:32:01:
I am a volunteer fireman just east of Lubbock Texas. Once a year one of the local power generating plants has a tour of the plant for the first responders in the district where they are located. They take us through the plant, in groups of about ten or less (easier to keep a watchful eye that way). Years ago they let us take cameras, but now, due to "homeland security" rules, we are allowed to take nothing that will take pictures. We can take our phones if they are turned off.
We were being shown a big row of what looked to me like large disconnects, each with a door on it about 2 feet wide and a big handle on the front. The one doing the talk put on two pairs of gloves, apron and face shield all the while talking about safety and precautions. On the floor there was a line painted in red that was labeled in a way that anyone crossing it without protective gear would be dismissed. OK, here we are, standing around this guy with all this protection on, and we are protected with only our earplugs and a few had redneck ball caps to protect their bald heads. I had the nerve to ask him about all of us, he kinda grinned, and let us know that bank of disconnects had all been de-energized for the tour, and went on to show us the procedure in doing so, so that he knew we were all safe in that location.
He also said, that in his 30 years of giving these tours, I was the first to ask that question...
I have seen arc flash up close and personal. We are taught how to remove a meter from a meter base at a fire scene. I had one arc all the way to the ground one night, about 5 feet of lightning that went all over the place. I had my bunker gear on with a face shield. We had reason to believe the place on fire was still "live". I took the handle of a fire axe, stood off to the side and knocked it down and away after breaking the seal. Never "assume" anything, as others have said as well.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.