Never saw 2 fences built the same. A good 5 strand is 48" high for non confined areas, T posts from 5'6" up in length and 6' min spacing, or stays at no more than 6' depending on how bad you want your animals to stay in, what's on the other side, and how easily they can be pushed over, aka soil conditions. A weight supporting post needs to occur periodically, especially in clay soils as the ground will crack open in the summer, posts will fall and in the winter it will close back. After a dozen seasons of that your fence is now 38 ft tall and your bottom strand is on the ground supporting your fence.
I liked double braces at each corner with a mid H brace every 300' max.
For standard breeds 10" off the ground for #1 and about 6" spacing. If calves, add a 6th strand splitting the 10". If you don't put that lower wire on they sometimes do their napping on the fence row and upon waking, get up on the wrong side. Rule of thumb is that if they get through it they can get back when they get hungry enough or mommy starts bellering at them, but when they wake up on the other side, they didn't get through it, they got under it and cows only go down in the pen......bears go down, bulls go up or through fences.
If you want them off the fence, (grass is ALWAYS greener on the other side), run a hot wire along the inside about half way up. Good grounding is important and in dry weather soil conduction is minimal and that's when you will have your biggest problems.
On open pasture, I have run what's called a swinging fence where the posts were 8-10". 3' deep and spaced 30 yards (giant steps) apart. Stays were between the posts spaced every 6'. When the cows pushed on it there was some give which helped it in doing it's job. With open pasture they weren't on the fence all that much anyway.
That's my experience, others have theirs....there is a story in every pasture.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Restoration Story: Fordson Major - by Anthony West. George bought his Fordson Major from a an implement sale about 18 years ago for £200.00 (UK). There is no known history regarding its origins or what service it had done, but the following work was undertaken alone to bring it up to show standard. From the engine number, it was found that this Major was produced late 1946. It was almost complete but had various parts that would definitely need replacing.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
