Posted by RBoots on April 23, 2017 at 19:46:26 from (173.241.113.102):
In Reply to: Depressing Day! posted by Bryce Frazier on April 23, 2017 at 12:18:49:
Well Bryce, that's too bad. I've had similar things happen. Not quite like that, but I know what you mean. I was putting the main shaft/pinion and countershaft back into a 450 IH I was working on when my dad came over. I had the countershaft back in and was getting ready to put the gears back on the main shaft. I had to leave for a little bit to go help my dad. I don't know what I was thinking, must have not been thinking, but when I got back to it, I slid 1st gear down the main shaft and then dropped all the others on. Got the rest of the stuff together, and slid the tractor back together, bolted it all up. Went to put the top cover on the trans, noticed I had put 1st gear on the shaft backwards. Lots of cussing for a bit, then I just decided to get after it, it wasn't going to work that way, or tear itself apart. I split it again, pulled the main shaft back out, slid all the gears off, flipped first gear, was going back together, and dropped the shaft with all the gears onto my finger which got stuck in between the shaft and the casting where the mainshaft bearing support goes. Well, that machined casting was as sharp as a razor on edge, and it just about cut through the joint of my middle finger. By now I was ready to be done, so I wrapped some tape around it, got the shaft in and slid it back together, then dropped the trans top cover down and bolted it up. By the time I was done, I had blood over every tool I'd used and all over that transmission. The anger within myself for such a stupid mistake made me just stick it out until it was a sealed up, moving unit again, which was my original goal. Sure it took much longer than I wanted to stay at the shop, but it was done correctly this time. Live and learn. I'll never laugh about that one though, I already have one finger I can't bend due to cutting it off when I was real little, and I couldn't bend that middle finger for a couple months, it really screwed that joint up.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Oil Bath Air Filters - by Chris Pratt. Some of us grew up thinking that an air filter was a paper thing that allowed air to pass while trapping dirt particles of a particles of a certain size. What a surprise to open up your first old tractor's air filter case and find a can that appears to be filled with the scrap metal swept from around a machine shop metal lathe. To top that off, you have a cup with oil in it ("why would you want to lubricate your carburetor?"). On closer examination (and some reading in a AC D-14 service manual), I found out that this is a pretty ingenious method of cleaning the air in the tractor's intake tract.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
