Posted by K Effective on May 25, 2017 at 05:05:34 from (162.235.236.141):
In Reply to: Stacking On Edge.... posted by Bill VA on May 24, 2017 at 18:25:02:
We pull the wagon right behind the baler. All bales on wagon on flat side for stability. Bottom layer five bales, middle bale north/south, four side bales east/west, string knot side up to take advantage of slight bow upwards. Next layer, bale on right side of the wagon n/s, four more e/w. Third layer bale on left side of wagon n/s, four more e/w. Layers three, four and five alternate, layer six is like the bottom layer, one in middle n/s four flanking e/w. Layer seven is only four bales, staggered over the middle bale of layer six, knots down. Can only get seven layers through the door on the pole barn, so we stop there, 34 bales per "rank". four ranks on a 16 foot wagon, with room for about 16 bales in the front with room to stand to finish that round, about 150 bales. Eighteen foot wagon will hold five full ranks plus bales in the front, about 180 bales. Each time you start a new rank, the second layer single n/s bale alternates to the other side. When I stack the wagon (most of the time), I also alternate the four e/w bales knots up and down, two of each on diagonal, and alternate those on the next layer, seems to keep the stack straighter. Nothing worse than a loose stack.
In our barn, roof ridge runs n/s, bales are stacked on edge (both edges have cut stems exposed, so no differentiating here), bales run e/w perpendicular to roof ridge. Layer first cutting across the whole floor, then second on top of that and then third, etc. Load the barn from the south, feed from the north end. When feeding, you have access to all cuttings of hay without digging and can mix it, or feed best off the top. Grandpa always thought bales on edge had a chance to dry even in the mow- at times with really damp second or third, I have stacked it on top of straw bales to draw the moisture out. That and air blown across the top does help.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Usin Your Implements: Bucket Loader - by Curtis Von Fange. Introduction: Dad was raised during the depression years of the thirties. As a kid he worked part time on a farm in Kansas doing many of the manual chores. Some of the more successful farmers of that day had a new time saving device called a tractor. It increased the farm productivity and, in general, made life easier because more work could be done with this 'mechanical beast'. My dad dreamed that some day he would have his own tractor with every implement he could get. When he rea
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
