1. I farm in TA very wet location, groundwater comes up out of the hills in spring when the 2-5 foot deep frost comes out and the snow melts. We have a short growing season here in Minnesota. Today is the longest sunlight, we have very long sunny days, but in spring and fall the days get really short.
There is little heat or sunlight in March early April. Ground is cold, water is cold, dirt is clay on top of clay for 130 feet.
We need heat and we need drying.
Only way to do that is some fall tillage, and again light tillage in spring. Get the little sun on the bare ground to warm it, and get the winds blowing across it.
If we had lighter soil, or less moisture, or less deep frost maybe notill would work.
But we have the perfect storm of conditions where no till doesn't work at all 2 out of 5 years.
You tell me which year is which in fall, and then I'll notill when I can. ;)
Notill is cheaper of course, but it can take a fairly expensive, well spec'ed planter to put in a crop in all the rough conditions the land needs to get a perfect stand. Less passes, less machinery needed, so it's a good thing where it works, saves time and money. Just can't do it if it prevents a person from planting until June or July.......
We don't use disks, they pack our clayish soils like a pavement. All field cultivators here, lift and stir, not pack.
Some folks have started rolling soybeans after seeding, it makes it easier to float the bean head over the field on fall. Seems to be some negatives to rolling corn tho, we don't do that here.
Mowing would seem to be a negative after seeding, but we learn new things as we go?
Spraying, get a taller sprayer, the self propelled you can drive a small car under them they go through tasseling corn....
All of this can apply to feed plots, it only takes money. ;)
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.