John good info, THANKS for that post, you're handy to have around. Your picture is something most engineers and electrical and automotive techs are familiar with, even if many non electrical trained gents may NOT be. Over the years I've seen several similar explanations to that you posted by different authors and vendors, but they all basically described the SAME concept. IE its best to operate a coil at the labeled polarity.
For any nay sayers who say it makes no difference, I would ask THEN WHY DO COIL MANUFACTURERS GO TO THE EXPENSE AND BOTHER TO LABEL COILS ?????? If it doesn't matter they wouldn't have to place + and - or BAT and DIST etc. on coils now would they ????
A few years back my late friend Duane Larson, a Nuclear Physicist, performed an experiment in his shop where he measured at what voltage a coil fired, and if the coil was at reverse polarity the voltage had to be a few thousand volts HIGHER !!!! In laymans terms at reverse polarity the coil had to "work harder" and run a tad hotter and it wasn't as efficient as if wired correct.
If anyone here is old enough to understand how vacuum tubes work, they know the reason why there's a heater under the Cathode, is because its easier to emit electrons off a relatively HOTTER (heated Cathode) to a relatively COOLER (Anode) surface, I believe that's referred to as thermionic emission. In an engine the plugs ground strap is much cooler then the tip sitting out there in the hotter combustion chamber.........
THAT BEING SAID HOWEVER as a past used tractor dealer and farmer and having seen and worked on literally hundreds of old truck n tractor coil ignitions (some wired right others not) they can still run at reverse coil polarity and to many non critical casual observers and users its NOT like the difference is night and day. Many might not ever know the difference LOL
Of course iffffffffffff ?? a magneto fires at each (BOTH North and South) rotor magnets passing, one spark is at one polarity and the other is reversed, but yet they still perform.
As an electrical engineer I must respectfully disagree with your opinion "nobody yet has a full understanding of how electricity works"
Hey we sent a man to the moon and are typing on our computers so even if you don't understand how electricity works, I disagree that "NOBODY" understands how it works lol. I will say that when I studied EE the absolute hardest subject I took was "SOLID STATE PHYSICS, ELECRTRONICS OF SOLIDS" That dealt with quantum mechanics and electron and particle theory and complex physics and so called electron and hole theory and even Maxwells Equations DEEP DEEP COMPLEX SUBJECT. BUTttttttt even if some students (MEEEEEE) didn't fully understand all that, OUR PROFESSOR SURE DID. Of course electron theory and solid state physics CAN NOTTTTTTTTTTT BE EXPLAINED HERE, it can take yearssssssssss to grasp such a deep subject so do not ask or even think I can explain it here lol.
You cant prove NOBODY understands how electricity works and I cant prove SOMEBODY understands, so we will just have to respectfully disagree and allow each other our own "opinions" NOT A PROBLEM FOR ME I'm NOT qualified to explain or prove it grrrrrrrrrrrrrr
Hope this helps gents understand why its best to operate an ignition coil at its labeled polarity even if it cant be explained here in a few sentences (but neither can brain surgery)
God Bless, Happy Easter
John T Toooooooooo long retired and rusty EE with "opinions" but don't ask me to prove or disprove them, I'm too darn old for that lol
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
