Installation shared on YT by a MEMBER of YT Group:
1955 Ferguson TO35, Power Steering?? ....SATURN ION ELECTRIC CONTROLL AND INSTALLATION
As you read through my posts you will notice that I am a Dutch-a-fied country person. The way I write a sentence may be hard for some people to understand. If you don't understand something please just ask me.
To start with the steering system has been installed at this time. I am finishing the wiring right now.
I started thinking about installing an EPS (Electric Power Steering) system after trying to drive my tractor around the house. So, I Google d “electric power steering” on the internet. What I found really excited me so I read everything I could find on line about this subject. I checked ebay and found the steering unit that I am using now. My unit is out of a 2005 Saturn Ion, normally you would need the computer out of the Saturn to help operate the EPS. But there is a small control and rheostat that is listed or ebay that will operate the EPS and it is listed in the same area that the steering units are listed.
My unit cost me $130.00 and the control cost about $70.00. The control comes from Portugal but don't worry this guy ships the controls right away. He will also send you a complete set of instructions.
My control took 4 or 5 days to get to my mailbox.
To start the alteration I removed the the steering wheel and the complete dash housing. Next the steering column was removed from the top of the transmission. The steering rod and screw was not removed. At this time I sucked the old fluid out of the steering box and installed about a quart of new 90 wt oil. Hello to all and Merry Christmas, I want to thank everyone that has offered me some words of wisdom the past few months regarding my 55 Ferguson. I have installed a new engine in it and it runs great. I am going to post a BEWARE sign right here about the following upgrade to my tractor. If you don' t like to see old tractors altered please close this page now. I will be altering the dash or cowl or whatever you may call it on my old tractor so I can install an Electric Power Steering (EPS) system. I knew the tractor steered hard when I bought it but I never realized it would wear me out in such a short time. My tractor has a front end loader that adds a lot of weight on the front wheels therefore making it hard to steer.
This project took me about 3 to 4 weeks to complete. I started looking at some old used power steering systems that were on other tractor. I decided I wasn't going to spend the money for a labor intensive and high maintenance hydraulic unit.
I goggled EPS and I found some 2002 to 2007 Saturn EPS units and a video on how they installed their EPS.
I will be writing in this post and adding pictures as I get time, please bear with me.
First thing is for me to learn how to post pic's on this forum. Next, there were two dash housing supports that connected the dash to the steering shaft housing. I used the right support which also held the choke rod, made it longer and bent it to fit to help support the dash housing.
On the left side I just made a new support and bolted it on. This made the dash housing very sturdy. Both supports are bolted through a steel tube that is manufactured in the steering unit. See the last picture, the tube is just under the output steering shaft and above the sleeve lying non the workbench. The next step is the steering wheel.
The steering wheel attached to the old tractor steering shaft by way of a tapered hole and key way. The new steering shaft has splines and the OD of it is .625. The steering wheel was bored out to remove the tapered hole, that made the ID of the steering wheel .812. I next turned a sleeve with an ID of .625 and an OD of .812. The sleeve was pressed into the wheel and tack welded on one end.
I wanted to make sure the steering wheel was nice and tight and not wobbly. So I welded two .375 x 1 inch x 2 inch pieces of steel to the outside of the steering wheel hub. I then cut out a .250 slice between the two pieces of steel. This makes the hub a clamp that will grip the steering shaft. Since there are no splines in the hub I drilled a small hole through the hub and shaft and tapped in a roll pin. I added a piece of 1.5 inch ID fuel hose on the steering shaft below the steering wheel.
I have NO connection I any way with the above info....but am amazed at an individuals ingenuity.:)
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Show Coverage: Journey to Ankeny - by Cindy Ladage. We left Illinois on the first day of July and headed north and west for Ankeny, Iowa. Minus two kids, we traveled light with only the youngest in tow. As long as a pool was at the end of our destination she was easy to please unlike the other two who have a multitude of requirements to travel with mom and dad. Amana Colonies served as a respite where we ate a family style lunch that sustained us with more food than could reasonably fit into our ample physiques. The show at Ankeny
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.