Rrlund - thanks. I think this will be a good move for us...I was gung-ho for a discbine a few years ago but the more I looked at the used market, the potential pitfalls etc..., I realized that the only way to go is new...or lightly used. This is what led us to the wider, center pivot sickle route. Hopefully the machine is as nice as it seems. Like I said, the other things with the discbine is it would mean a 2nd bigger tractor (I hate having anything on the farm that I can't have a backup for (i.e. - more than 1 option to run it)).
Everyone else...I truly have no idea how this is going to pencil out...i can't imagine it will...we are in upstate NY, local market on nice 1st cut is $3-4/bale, 2nd is $4-5/bale. He plans to send it to the cape cod area which I think is more of a $6-8 and $8-10 market for first and 2nd. We have struggled the last few years with the weather to get our first cut in early....so perhaps round baling will allow him to attack his first a little faster.
I was thinking maybe he will have a long pole barn, setupt a massive conveyor belt with an astroturf surface...stationary high capacity square baler, a stationary rake and a round bale on a spool at the far end. Conveyor takes hay off the round bale, fluffed/merged by the rake into the square baler, dropped on the conveyor behind it to the waiting stacker...lol. Other than that setup...I can't imagine this not being a labor intensive method...
I am interested...wish the guy was a little more local to me so I could watch from a close distance.
I am going to talk to a buddy at the local JD dealer to see if he knows the scoop. I assume he is a fan of this guy...at least right now when the payments are coming through.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Profile: Farmall M - by Staff. H so that mountable implements were interchaneable. The Farmall M was most popular with large-acreage row-crop farmers. It was powered by either a high-compression gas engine or a distillate version with lower compression. Options included the Lift-All hydraulic system, a belt pulley, PTO, rubber tires, starter, lights and a swinging drawbar. It could be ordered in the high-crop, wide-front or tricycle configurations. The high-crop version was called a Model MV.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.