Posted by paul on April 20, 2018 at 11:00:04 from (76.77.201.215):
In Reply to: OT: Pole Barn In Stages? posted by Ken Christopherson on April 20, 2018 at 09:26:39:
A few things to consider.
The siding and the 2x the siding is hung on is part of what gives a building its integrity.
If you build a roof on poles, like a hay shed, no sides, you need a little stronger materials to start with. So the whole thing will cost you more.
Wind. A free roof catches a lot of wind, you moght need to strap the roof down a little better, might even need the poles anchored better. Again, takes a little more money for the details.
My 48x81 building has poles and trusses spaced at 9 feet. And I'm in Minnesota. It uses top quality wood, not the bent knotted stuff from the picked through standard pile at Menards. A designer can get the best bang for the buck with the many different designs and spacings possible. You need to match your spacing to your trusses.
To be honest, for a smaller shed like you propose, you might want to pour a foundation, use 2x6 and just build it conventionally, order trusses and set them up. You indicate you are on a budget, if you are doing the labor free this might pencil out the best.
When I built mine I did the electrical and 1/3 cement floor a year later. Don't wait longer than that. You will layer up the shed with so much stuff you won't want to move it all out to get the concrete in......
I would consider long and hard on getting it all built, the whole shell, right off. The poles (or 2x6) and trusses and roof is most of the money, all that's left is a little more tin and a few 2x nailers for the side tin..... and might be cheaper parts with the sidewalls part of the stiffening from the get go.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - 12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.