Posted by JML755 on July 24, 2018 at 07:54:05 from (166.137.12.85):
In Reply to: Power.. yay posted by Justinwheeler on July 23, 2018 at 20:10:57:
DTE (Michigan electric utility) has a continual trimming policy trying to keep the lines clear. I think 10' is the distance they use. Driving down my road, there are trees right next to the pole line with big "holes" cut right around the lines.
I'm getting a "line extension" of about 650' from the main line along the road into my property. Utility is coming out this week to mark the poles (4) and it will be 6-8 weeks from then when they set them. The 12' easement runs along the property line with a neighbor that was pretty overgrown for about 220'. I cleared 20' in that area (probably 50-60 trees) to allow trucks to go down the easement when they install the poles/line but there are still branches from the neighbors trees that encroach into the easement. I spoke to the planner and told her that my property is clear but mentioned the trees on the neighbor's side that may be a problem. Utility charges $85 to trim a tree as part of their "line clearance costs", removal: 4” to 10” circumference at 75.00 per tree, up to 32” for $1500 so I want to do as much of the "line clearance" myself as possible.
There is a tree on my property that I'm hoping we just have to trim. It's over 65' tall and $85 is a bargain to let them do that. (The actual line is 45' high.) If it's got to be cut down, I'm on the fence about whether to do it myself or hire someone. I've cut trees up to about 18" and it's a nerve wracking experience for the big ones especially if they want to go in a direction you don't want them to go. :o This one is about 24" in diameter. It's no big deal to have it drop on my property, it's all open field. If it goes onto the neighbor's property, it's also field but I'd have to drive around the fence to clear it: not as efficient.
Anyway, I've budgeted a few extra hundred bucks for line clearance above and beyond the installation costs which are pretty reasonable, IMO. It'll cost $2400 to put the new poles in and setup for 320A service. Going underground from the last pole/transformer to the house will be another $800 or so.
Anyway, I'm all for keeping the lines clear. We've lost power a few times the last couple of years and it's ALWAYS due to a tree coming down on a line due to wind and/or ice.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Hydraulics - Cylinder Anatomy - by Curtis von Fange. Lets make one more addition to our series on hydraulics. Ive noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.