Posted by farmersamm on November 01, 2018 at 11:54:35 from (206.246.18.143):
In Reply to: Plowing posted by SVcummins on October 31, 2018 at 07:54:19:
Got you some pics. Been a while since the ol' gal has been in the ground.
When setting one of these up (this happens to be an old Raydex), you need to level them.
Drop it, and run for a bit. Stand back, and look at how level the bottoms are. A rollover is easy to see.
Posted this pic down in the equipment forums, but it's a good example of how it should look.
See how the bottoms are level on the horizon, while the tractor is tilted down in the furrow.
My adjustments are probably different than yours, bein' as it's an Oliver plow, but you can see how there is a provision for leveling the plow. In this case....stop bolts.
Also, notice how the hitch assembly is tilted in comparison to the body of the plow. That's your offset to take care of the difference between plow running flat, and how the tractor has it's wheels down in the furrow.
Just as a side note...…..You can see just how level you're set up, by looking at your bottoms. They should be wearing relatively evenly along the edge.
Once you start wearing into the hooked/curved forward edge of the bottom, it's usually time to put some new shares on. It won't wanna suck down into the ground once these hooks wear down too far.
BTW, here's that crazy gage wheel. Drive ya nuts sometimes when it doesn't latch.
Anyways, hope it helps. I don't imagine there's many folks running these nowdays, not sure (shrug)
Got no excuse now, the drizzle stopped, and the sun's out. For now :lol:
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Timing Your Magneto Ignition Tractor - by Chris Pratt. If you have done major engine work or restored your tractor, chances are you removed the magneto and spark plug wires and eventually reached the point where you had to put it all back together and make it run. On our first cosmetic restoration, not having a manual, we carefully marked the wires, taped the magneto in the position it came off, and were careful not to turn the engine over while we had these components off. We thought we could get by with this since the engine ran perfectly and would not need any internal work. After the cleanup and painting was done, we began reassembly and finally came to t
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.