Posted by INCase on January 14, 2019 at 08:00:32 from (209.221.240.193):
In Reply to: Bethlehem steel plant posted by larry@stinescorner on January 12, 2019 at 17:07:06:
I would love to see that. Would never get the wife to stop there. >reading/watching the background and history of steel making process thru the innovations and building is pretty neat stuff. from the basics of steel making when Bessimer invented the blast furnace to Carnegie building his steel empire and being on the fore front at the right time and place in history. Those plants including the ones built along the lake in NW Indiana are impressive. the books on how the Indiana Steel mills were built is amazing.
family is from NE Ohio and when i was going to school in Youngstown there were a couple blast furnaces still standing. they were neat but kinda creapy/ghostly landmarks. i think they've knocked them all down now. i remember alot of the "lost" pensions being in the news. Pensions aren't really guaranteed. i know some wanted GM to go bankrupt to let them get out of some of the union contracts and pension loads. not right but we cannot trust the goobberment to "take care" of the pensions either. save it for yourself. THat's what my company does. they put 5% of my pay in a "pension" account that is kinda like a 401k (has a different 401? number) that i can take with me. I know i'm a lucky one.
even going to a "small" modern casting plant is impressive that they can heat, melt, control content and quality and then pour that iron like it was water into the sand molds.
i was watching them load the cupila (sp) they would put some iron ore, some scrap iron, some scrap steel a little of this and that. saw the magnet in the scrap area pick up a complete snow plow mount from a pickup and put it right in the furnace. hoses, motor, headlights the whole thing.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.