Posted by pburchett on January 27, 2019 at 17:29:11 from (12.182.196.81):
I started working on the 640 ford while it is cold. I pulled it into the barn and was going to replace the inner seals in the rear end to stop the gear oil leak and replace the PTO seal.
Since it was cold and the front of the tractor was closer to the wood stove I packed the front wheel bearings. Of course the spindles were a little sloppy so I rebuilt the spindles. The bushings did not look bad but the new ones took the slop out.
Well as I get to poking around it appears the front axle pin and bushing are in need of attention. Off comes the sheet metal and the rear fenders. I need to patch some holes in one fender any way and the lift needs fixed and think it would be easier to reach with the fender off.
While hammering on the axle pin the radiator starts seeping. I am tired of the rotten radiator so I ordered a new one. Should be here soon.
Got the pin and bushing out. Looks like I got the best out of the bushing.
I now need to add that to my YT parts list that includes seals, gaskets, clutch, pressure plate, tune up kit, proof meter and a bunch of other stuff.
While looking around the engine I noticed that every gasket looks to be seeping some. I had planned on ordering a complete gasket kit. Maybe I can paint it after I get the oil leaks down to a minimum.
Then I get to thinking…Should I freshen up the old motor with a new set of rings and lap and adjust the valves? I only need to unbolt the engine and I have to inspect the clutch before ordering one. It doesn’t smoke, does not leak much out the rear main (quarter size spot after a hard work out), has some blow-by, and only uses 1 1/2 quarts of oil in 100 hours. It holds 40 psi oil pressure with 15W-40 no matter how hot or how hard I work it. It is 65 years old and I could mess something up. It is not my main tractor as I have the new MX5200 Kubota. So then I wonder if I would be better off leaving the engine alone till it needs something major?
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Old Time Threshing - by Anthony West. A lovely harvest evening late September 1947, I was a school boy, like all school boys I loved harvest time. The golden corn ripens well and early, the stoking, stacking,.... the drawing in with the tractors and trailers and a few buck rakes thrown in, and possibly a heavy horse. It would be a great day for the collies and the terrier dogs, rats and mice would be at the bottom of the stacks so the dogs, would have a busy time hunting and killing, all the corn was gathered and ricked in what we c
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
