Posted by Sprint 6 on February 03, 2019 at 06:46:16 from (107.77.195.32):
In Reply to: Re: Cummins 53 block posted by SVcummins on February 02, 2019 at 16:44:44:
Where can I buy a 24V for $2500? I'll take all I can get at that price, any 5.9 sells for $3500 in my area. The only truly reliable 5.9 was 94 to early 98 with the P pump. The early rotary VP was power limited and failure prone, the later VE was handicapped by the crap Dodge supply pump. The later common rail system was pioneered by the Duramax. The Duramax trucks were what forced Dodge and Ford to put a real drive line in their trucks. What good is a 300K+ engine when it is bolted to a 50K transmission? I believe if GM would have straight axled the HD 4x4, there would be no Ram truck today, the Super Duty line may have died with the 6.0 if not for the straight axle. The IFS is the Achilles heal of the GM HD line.
Comparing the 6.5 to the 5.9 is not apples to apples other than the fuel they burn. The 5.9 was designed as an industrial engine. The 6.5 was designed for weight, size, fuel mileage, and have the power of a 350 gasser. When looked at like that, the 6.5 Turbo did it's job. I have one I serviced regularly that was past 350K when I told him to ditch it because the body was shot. Engine was all original, including the pump. He ran a quart of ATF in every tank of fuel since it was new. Your failure prone 6.5 was probably due to a bad harmonic balancer, which was then transferred to the replacement engine to work it's magic again. The rubber breaks down on the balancer, then the crank breaks. The largest problem with the 6.5 is the cooling system, it has to be tip top due to the hot nature of a pre-combustion engine. Same as the IDI 6.9 and 7.3 Ford.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Hydraulics - Cylinder Anatomy - by Curtis von Fange. Let’s make one more addition to our series on hydraulics. I’ve noticed a few questions in the comment section that could pertain to hydraulic cylinders so I thought we could take a short look at this real workhorse of the circuit. Cylinders are the reason for the hydraulic circuit. They take the fluid power delivered from the pump and magically change it into mechanical power. There are many types of cylinders that one might run across on a farm scenario. Each one could take a chapter in
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
