Posted by 300jk on March 08, 2019 at 15:37:35 from (172.56.22.153):
In Reply to: Paving Driveway posted by nrowles on March 08, 2019 at 12:13:47:
I have never paved a driveway. I have though been in heavy highway construction for 22 years and put down 10's of thousands of tons in roads and highways. Mark in Upstate is the closest to what I have done in the past. Box out(remove dirt) and compact. Add crushed 2" stone (Usually 6 to 8") compact stone. Fabric is used for soil stabilization in soft areas if necessary. Usually the inspector wants to see a "proof roll after the stone is graded. That would be a loaded 10 wheel dump truck driving on the area slowly while he watches. If is does move or the truck sinks the area is dug down deeper and more stone added. Once approved then paving with 3 layers. Base, binder, and top. Most local roads here have 8 inches of blacktop when done. Highways and interstates usually more. While 8 inches is overkill for most driveways I would be scared of putting down only 3. I know I added a lot of what might seem like useless info, but if it was mine that's how it would be done. The biggest thing is a HARD, STABLE base under it. The price you were quoted seems kinda high for what your getting, but I am not sure what the materials are going for where your at now. Most driveways probably won't fail during the warranty they give you if they give you one at all. Could be a few years down the road. I would hate to see you spend that kind of money and end up with a poor quality job that falls apart in 6 or 8 years. I am not trying to be a know it all, I'm just telling you my personal experience and what I do factually know.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - A Belt Pulley? Really Doing Something? - by Chris Pratt. Belt Pulleys! Most of us conjure up a picture of a massive thresher with a wide belt lazily arching to a tractor 35 feet away throwing a cloud of dust, straw and grain, and while nostalgic, not too practical a method of using our tractors. While this may have been the bread and butter of the belt work in the past (since this is what made the money on many farms), the smaller tasks may have been and still can be its real claim to fame. The thresher would bring in the harvest (and income) once a y
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
