You do NOT need a double acting cylinder at any time on that disk unless you are trying to carry the wheel for extra weight for penetration in hard ground. For normal plowed ground you want to have the wheels actually carring the weight so the disk is not trying to cut over 3" deep, 4" max and that disk with decent blades not wore out with out the wheels partily carring the disk it would want to cut6" or more deep and you dont need that for any crop that I know of. And not pulling strait (tracking) tires that are not matched in size will make it so one side wants to cut deeper than the other and side cutting deeper will pull harder to make the tracking off to side. Yes you do have to level it. And that model being a non adjustable angle disk will always even set correctly will ridge especially at higher speeds. And the back blades on the outside will always leave a furrow due to angle of blade and center of disk will leave a ridge if too fast of travel as it will throw the dirt to far and double up what it should be doing. Those disks being a rigid frame with non adjustable gang angle were never a good finnishing disk like the KBA that you thought it was. Ford pentration it is better than the KBA. I had the KBA in both the wheel carried and pull type with out the wheel carrier and that was always my last time over finnishing disdk as it could be set with the gangs fairly strait and it would still penetrate and not do the ridging in center or furrows at outside. I had a McCormick No. 37 disk that was a heavier disk and rigid frame like yours but with adjustable angle gangs and I never ran it with full angle on the guangs as that takes more power to pull and being ridgid it would always if toy were doing any turning ridge and leave more of a furrow, I also had a Burch and Kewanee disk both ridiged frame and non adjustable gang angle and they did not stay around too long. And get yourself some duals on rear of that tractor as it will realy help with the ride and also with traction and in helping with the raction will cut your fuel usage. And your tractor is made for a high pressure single action cylinder so you could NOT use a double acting cylinder with factory setup on hydrilics. Only thing is an 8" cylinder on any older implements as a 10" stroke could break the frame of the inplement. First diked 60 some years ago. Lots of experiance with many a disk.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Grain Threshing in the Early 40's - by Jerry D. Coleman. How many of you can sit there and say that you have plowed with a mule? Well I would say not many, but maybe a few. This story is about the day my Grandfather Brown (true name) decided along with my parents to purchase a new Ford tractor. It wasn't really new except to us. The year was about 1967 and my father found a good used Ford 601 tractor to use on the farm instead of "Bob", our old mule. Now my grandfather had had this mule since the mid 40's and he was getting some age on him. S
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.