Tractor Talk Discussion Board |
Re: Homemade Tractor
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Hal/WA on December 10, 2001 at 11:43:19 from (208.8.194.16):
In Reply to: Homemade Tractor posted by Chris on December 09, 2001 at 20:34:43:
Years ago some friends of mine built a homemade tractor out of an old IHC medium sized truck that had been rolled over and the body ruined. They used the front end without much modification except the removal of fenders, but the frame was shortened to about tractor length and the rear axle was mounted solidly to the frame. In order to get the gear ratio right for a tractor, they mounted a second 4 speed transmission to the output shaft of the original transmission (I think they just welded them together!). Then a short drivesaft connected to the rearend. They used the original dual tires, chained up all the time, for traction and had cast a block of concrete that probably weighed a couple of tons above the rear wheels. The engine was the IHC flathead 6, that never left the chassis. I don't think they had a governor and the hitch was pretty basic, since their implements were way old. With the first transmission in 2nd and the second trans in compound, the tractor would plow fine with 3 or 4 plows. On the other hand, the machine would FLY with both transmissions in 4th. My friends did not use hydraulics or a PTO. The only problems they really had with it had to do with brakes. I have thought that it would be fun and easy to do something similar. I would use the pto from whichever transmission that would get the RPM's about right to do a tractor type pto. For Hydraulics, I believe a pump could be mounted on the front of the crankshaft. There are kits to adapt older tractors for 3 point equipment. I think a governor could be set up using cruise control parts. I would cover the rear tires, because the old machine really threw mud and dust all over us!
Follow Ups:
Home
| Forums
Today's Featured Article -
When Push Comes to Shove - by Dave Patterson. When I was a “kid” (still am to a deree) about two I guess, my parents couldn’t find me one day. They were horrified (we lived by the railroad), my mother thought the worst: "He’s been run over by a train, he’s gone forever!" Where did they find me? Perched up on the seat of the tractor. I’d probably plowed about 3000 acres (in my head anyway) by the time they found me. This is where my love for tractors started and has only gotten worse in my tender 50 yrs on this “green planet”. I’m par
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|