Posted by Janicholson on July 31, 2019 at 18:55:34 from (24.240.46.228):
In Reply to: Super H brakes posted by yeld on July 31, 2019 at 18:34:10:
Long bolts don't heat affect very well, so getting them red may not do it. I think I would use a Oxy/acetylene cutting torch to blow the heads off. once off, you can remove the housing. With the housing off, you can heat them and cool them heat them and cool them about 4 times from red to cold. each time when still pretty hot, melt a candle on the bolt at the threads to get it to soak in. Then use a vice grip to back and forth them till they move. The brakes may need a new set of disks. If the disks look fat, do the following: With the housing supported on the bench on its back (where the little cap is located) so that it stays horizontal, put all the parts inside it in order, and centered. Now measure with a straight edge across the housing, from the edge of the housing on its now upper surface, down to the top of the friction disk. With new discs or old, the space should be between .030, and .045" if it is more, the housing needs to be machined to make that specification. The expander needs to have all its springs around the outside. It also needs its balls checked for roundness and polished. The ramps need to be smooth and have no dents or depressions in them. A spray of Dry lube like Triflow, is all they need to be fine. Use a 200 or 250 grit disk or other non directional process to out surface "sanding swirls on the metal of the expander, and the friction discs surfaces to break the glaze. Dry lube on the linkage pivots, and anti seize on the adjuster threads. Jim
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Grain Threshing in the Early 40's - by Jerry D. Coleman. How many of you can sit there and say that you have plowed with a mule? Well I would say not many, but maybe a few. This story is about the day my Grandfather Brown (true name) decided along with my parents to purchase a new Ford tractor. It wasn't really new except to us. The year was about 1967 and my father found a good used Ford 601 tractor to use on the farm instead of "Bob", our old mule. Now my grandfather had had this mule since the mid 40's and he was getting some age on him. S
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
