Posted by modirt on August 24, 2019 at 11:34:23 from (199.187.163.74):
In Reply to: Got a baler posted by Grandpa love on August 23, 2019 at 18:21:49:
I went looking for a baler a year or so ago and settled on a NH 315. It is the real deal as far as older square balers go. Meant to handle volume.....for example, twine box holds 3 spools vs. 2. This is what it did for me earlier this year.....
Agree with everything the others have said about it's ability, etc. I have used 3 tractors on it. Last year, the neighbor's 1100 Massey.....and that was a dream. The Massey has near perfect gear range for baling....with a high low range to step it up and down for the windrow.....plus it has the heft to handle it. The whole experience was smooth as silk.
Since then, I bought a Ford 5610 and baled with it this year. Handled it ok, but you knew it was back there. I also pulled it out earlier with the D15 Allis to rebale some loose busted bales in a stack. Sitting still, baler was rocking the D15 several inches per stroke......I would not want to bale with it. Would not be kind to the old girl. A D17 would be a better fit. I know a guy with a White 2-70 I'm trying to goad into letting me try on it.......purely for educational purposes you understand.
As for what to do.....if the baler has been sitting in the barn for a few years, you appear to have two paths to follow. The high risk plan is to assume it was baling OK when last used and would do so again. Grease it and go.
Safer plan is to take no chances, at the minimum, pull the old hay out, turn it over by hand to make sure all is working ok, trip the knotters while someone is turning it over by hand to see if it ties good knots. BTW, if the twine that was in it was sisal, I'd assume it is rotted enough I would start over with fresh. Sisal or plastic will work ok.......just get the 170# plastic.....not the thin stuff used in round balers. Basically do a full walk through to recommission it. When they are working right, they will spit bales out one after another with no worries. But when something goes wrong, it goes wrong in spectacular fashion.
Mine kept breaking shear pins......and while I was able to figure it out and get it working right, I decided to bring in a better set of eyes than mine to go over it. Good that I did as it was in need of some attention. In all, three guys with about 150 years combined experience between them helped me go through the entire baler......replaced plunger knives (and set knife clearance to specs)...... replaced plunger bearings......went through the knotters, timed the needles, checked slip clutches to make sure they would slip before something broke, etc.....in short, is back to almost new condition and it behaves as such.
Bottom line is you have assumed stewardship of a dang nice baler........it you do your part, it will spit out bricks.
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Restoration Story: Fordson Major - by Anthony West. George bought his Fordson Major from a an implement sale about 18 years ago for £200.00 (UK). There is no known history regarding its origins or what service it had done, but the following work was undertaken alone to bring it up to show standard. From the engine number, it was found that this Major was produced late 1946. It was almost complete but had various parts that would definitely need replacing.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
