Posted by TimWafer on November 27, 2019 at 07:17:06 from (98.21.118.93):
Sorry for the long story here.
Where I work, we sell propane. Therefore we end up with a lot of old propane tanks which I have always added to my scrap metal loads. I came up with a system to remove the valves and break the tank down into 3 components for scrap. The steel tank, the brass valve and the aluminum handle. When set up for a batch it takes me an average of 3 minutes to break a tank down. The valve has always been the most valuable part and is currently over twice as valuable as the tank itself. This has worked well for years.
Monday I took in a load of scrap and had about 35-40 tanks thrown in it. The man at the scale comes out and informs me that they can no longer accept propane tanks unless they are physically cut in half. We discussed this at length but he said that the word came down from headquarters that because they had 8 different explosions due to propane tanks at there shredder plant that they cant accept tanks unless cut in half even if the valves are removed. I was told I could dump my load but would have to sort out all the tanks and take them back with me. So that s what I reluctantly started to do. While sorting out the tanks the loader driver at the scrap pile stopped and got out of his cab and asked me what I was doing. I told him and he said that was crazy and they were fine as long as the valves were removed. He said to leave them and he would shove them into the pile and it was then out of my hands as I wouldn t be allowed to touch them. This suited me so its what I did.
Upon returning to the scale, the attendant was upset that I didn t retrieve the tanks so I told him the whole story and that they would have to work it out among themselves as I was out of picture at this point . He agreed .
So I made out fine this time but my concern is with the next load of tanks. Im trying to think if there is a way to easily, safely and quickly cut a tank in two to satisfy them. I mean I have cut tanks up in the past for various uses but always spent a lot of time purging the tank first using various means. None of those means would be practical just doing it for scrap.
Looking for some innovative way to do this that would be practical. I have lots of tools at my disposal. Any suggestions?
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Grain Threshing in the Early 40's - by Jerry D. Coleman. How many of you can sit there and say that you have plowed with a mule? Well I would say not many, but maybe a few. This story is about the day my Grandfather Brown (true name) decided along with my parents to purchase a new Ford tractor. It wasn't really new except to us. The year was about 1967 and my father found a good used Ford 601 tractor to use on the farm instead of "Bob", our old mule. Now my grandfather had had this mule since the mid 40's and he was getting some age on him. S
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.