Posted by Billy NY on November 30, 2019 at 06:49:31 from (74.70.87.149):
In Reply to: Bought a couple plows posted by Grandpa love on November 29, 2019 at 04:52:10:
Kevin, that is an excellent buy !!! I can tell by the leading edge on the moldboard plow, appears to have like new or very good condition share and shin. You can easily tell if they are worn as they won't project far enough beyond the frog/standard, and that is what will wear next. Wear parts are available for this plow.
The 101 Ford plow is a very nice plow, it's trip back protected, vs shear bolt, (though I have run my shear bolt protected Ford 110 in rocky conditions and never sheared a bolt, only roots seem to cause that to happen). Adjusted properly, it should pull very nicely and I would bet you'll master the use of it easily. My 110 does a very nice job, pulls like it's not ever there. I have yet to master the 101 2 bottom plow, close but need to get both plows taking an even bite and turn it over correctly consistently. I have taken video while plowing and have seen where it was close, but cannot top the single bottom yet. It's in the adjustment and it seems I cannot let the top link out far enough to level it even though I have done so with an 8" block under a wheel on flat pavement.
Wire wheel off the rust, flap disk it, then have at it in the soil, hopefully you have some abrasive soil down there, otherwise you'll want to clean and polish further. I paint mine when done to keep it from rusting, lasts for years outside. There is a grease Zerk for the trip back mechanism, you may want to check that out, see how it trips, make sure it works. Check the wear on the landside, they wear significantly too, cannot see the bottom of it in the photo. The tail wheel should relieve pressure on the bottom of the landside, but they eventually wear. I rebuilt a 2 bottom version of this for just under $200 in '12, shins, shares, and landsides with all new bolts and I did coat the bolts heavily with anti seize.
I have the same subsoiler, later one in blue paid $125 for it 10 years ago, bought it with the 110 plow from the same guy. I've never used it as it is NOS. I also have another 110 plow that was used 1 time, they found they had ledge rock, broke the tip of the share off, never used it again. Yours looks like the reversible wear shank tooth has only been worn on one side yet, the main shank does not seem to show a lot of wear. The weather seems to have worn both these more than anything else, must be that humid air. Another great implement, that is shear bolt protected as well. Be careful with it, no ROPS/Seatbelt on your tractors, believe these take grade 2 bolts which should shear easily if you hit an obstruction. I think I have a manual for it in my stash, just a 1 or 2 page sheet.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
