Posted by K Effective on April 06, 2020 at 06:52:24 from (99.184.108.123):
I've been contemplating fencing off the fields in front of our house, north of the driveway out to the road. It's about ten acres, currently in a small hay field and small bean field. Directly east of this ground is access to my pastures- I'd like the option of turning the cattle out on these two small fields in the fall, either to graze cornstalks or a hay field if conditions warrant. Plus, it would be a small amount of insurance if a cow finds a weakness in the fence perimeter and goes on a walk-about.
We have access to the fields from the south east and west corners- pretty convenient to pull in with a tillage tool/planter/combine from either side.
I want to set the fence up with gates at those two spots for vehicle access, plus others for the cattle to use. My question is- what should I plan for gate access to accommodate today's large equipment, and the future's designs, as well?
I was thinking of using two gates at each access, like JonMN was showing in his thread. I like steel tube gates, and the fence will likely be tensile wire. The neighbor has the combine, and his grain table is 35' wide. Would two 20-foot wide gates give me enough room? I could plan for a removable post in the center for support.
Is there some better arrangement than two gates? Should I just plan for him to take the head off and cart it into the field to hook back up? The east gate access can be used from his fields directly to mine, no road travel needed. The west gate would be right off the road at my driveway. Maybe I should set the opening at 50 feet, and just run wires through there when needed- most of the year there would be no cows in there, only if they escaped the pasture. I could install the temporary 50 feet of wires as needed, and leave it open most of the year. I don't trust the fence or animals enough to just use temporary fence for all of it, only as needed.
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
