Posted by Dave41A on April 14, 2020 at 07:18:30 from (71.161.70.176):
In Reply to: Chain Saw Help posted by Dave41A on April 13, 2020 at 09:37:40:
As a follow-up to everyone who responded, I took the suggestion of using gas instead of starting fluid. I poured about a teaspoon down into the carb body/choke opening. Then after a few pulls it fired and would even run at idle for maybe 10 seconds. Took out the NGK plug and put in a champion--made no difference, so put the NGK plug back in.
I took a look at the Walbro carb linkage and found that the choke lever was binding/hitting on the inside of the air cleaner assembly (a piece of plastic). This prevented the choke from fully closing, and also did not allow the lever on the choke plate shaft to "latch" with the throttle shaft to "set the throttle." This is unrelated to the current problem but does explain why the saw was always hard to start when hot, as the choke is supposed to hold the throttle open about 1/4 until the handle is squeezed, releasing the choke and the throttle at the same time. I ground the plastic away in the offending spot with a rotary grinder and after some trial and error can now set the choke and throttle like I should.
Anyway, I can now get the saw to reliably start, but it will only run at half choke, and then only for 20 seconds or so. After squeezing the throttle lever and dropping to low idle it will stall. So I am thinking there must be some obstruction in the carb idle jets still in there and/or a pinhole leak in the gas lines that is interfering with good fuel flow and/or a diaphragm problem (or all three). I tried it with the fuel filter removed and that made no difference, so I do not think it is the filter, although it is the original (5 yrs old) so probably time for replacement anyway.
It will be a few days yet when I get back to this but will post my results if/when I make any progress for the benefit of anyone with a similar problem. Thanks to everyone with the good suggestions. I learned something about cord wood houses anyway. Pretty interesting--but looks like a lot of work. Dave
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Product Review: Black Tire Paint - by Staff. I have been fortunate in that two of my tractors have had rear tires that were in great shape when I bought the tractor. My model "H" even had the old style fronts with plenty of tread. My "L" fronts were mismatched Sears Guardsman snow tires, which I promptly tossed. Well, although these tires were in good shape as far as tread was concerned, they looked real sad. All were flat, but new tubes fixed that. In addition to years and years of scuffing and fading, they had paint splattered on
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
