Posted by bc on December 21, 2020 at 08:08:42 from (45.21.235.60):
In Reply to: OT land surveying posted by steve-in-ga on December 21, 2020 at 06:33:05:
I'm got new fence to put up and have a hill in KS to deal with. Well more like about a 25' rise. I suppose every property line in GA has a hill in it.
Where a tree has grown around on marker, I can offset about 6'. I've also tried running a laser at night. Have a star spotter that would probably laze for a quarter mile except for the hill. Once a laser is set up, I can mark the post placements very easy. Lasers don't go through dirt is the problem and can't guarantee stakes are perfectly vertical.
I've used construction transits. You know it is level when you can swing from one corner of a building and back and hit the starting spot again. They are available and cheap since most have gone to lasers.
I'll check on a surveyor's transit which may be the same as a builder's. Guess I'm kind of a rear end about accuracy. Can you accurately swing a transit around exactly 180 degrees exactly? I'd hate to think my line was more than an inch off for a 1320' run. I'd still put the fence in a little from the line but still nice to know how far inside it is. In some places, the fence becomes the property line so you have to be careful where you put it as much as I'd like to be able to run a mower on both sides and be on my property but then the pheasant people don't want fence lines mowed.
I think anymore if the county commission had to settle a fence dispute, they would send out the county surveyor who would be using his dgps or whatever to find the lines. They probably wouldn't even come out.
Most cities and counties have all properties laid out on a GIS system that you can access online usually through the assessors or treasurers offices. You can turn on satellite view with the line overlay. That can get you close. But they can be off of the property pins as well. Problem is that the width of the line can be a foot on the ground but it will get you close. Even a pencil line on a topo map is a few feet wide on the ground.
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Restoration Story: Fordson Major - by Anthony West. George bought his Fordson Major from a an implement sale about 18 years ago for £200.00 (UK). There is no known history regarding its origins or what service it had done, but the following work was undertaken alone to bring it up to show standard. From the engine number, it was found that this Major was produced late 1946. It was almost complete but had various parts that would definitely need replacing.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.