Posted by bc on May 24, 2021 at 06:59:13 from (24.255.129.137):
In Reply to: Building a dock posted by chuck t on May 22, 2021 at 18:43:23:
Couldn't resist the math problem. 55 gallon X 8.6 is 473 divided by 2 is 236 pounds of displacement per barrel at half way. 6 barrels is 1,416 pounds of displacement.
30' trailer with maybe 6" C channel frame. 60' of 6" C channel at 8.2 pounds per foot is 492 pounds. Add the lighter cross members and figure around 600 pounds for the frame.
Treated 2by6's at 8' long weigh 14 pounds each. 60 2by6's X 14 equals 840 pounds.
600 plus 840 equals 1440 pounds. So about 6 barrels to float the dock around half deep. Add a couple guys on the dock fishing and you get another 2 barrels but may be too high when empty. The blue plastic barrels are just over 23" in diameter and 34" long. The dock would put the barrels about 12" or so in the water with 11" above. I wouldn't think a couple guys fishing on the dock would drop the dock more than a couple more inches. That would be for a floating dock not touching land.
The trick would be barrel placement allowing for the slope of the pond. Figuring you anchor one end on the ground you won't need to support the entire weight of the dock and the barrels would have to be in water over 12" or more deep to float. You could maybe get by with 4 barrels but I'd go with 6. If two guys are on the end of the dock fishing then I'd want 3 barrels across the end and another 3 about half way back. If you wanted the whole dock to float, then I'd still put 3 barrels on the end where people would stand which would be a total of 7 barrels or float it higher and go with 9 barrels.
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Timing Your Magneto Ignition Tractor - by Chris Pratt. If you have done major engine work or restored your tractor, chances are you removed the magneto and spark plug wires and eventually reached the point where you had to put it all back together and make it run. On our first cosmetic restoration, not having a manual, we carefully marked the wires, taped the magneto in the position it came off, and were careful not to turn the engine over while we had these components off. We thought we could get by with this since the engine ran perfectly and would not need any internal work. After the cleanup and painting was done, we began reassembly and finally came to t
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.