Gerald that would take all day since they use several ways to harvest cane depending on what they are using it for.
But lest stick with this Green Harvester in the picture. Green as in fresh cane; not burned down.
Around here cane is planted in August and harvested from Sept to January all though they try to finish by Christmas. They get 3 cuttings on a 4 year rotation from one planting. So the field lays fallow from Sept to the next August 1 year out of 4. They use this time to chisel plow; clean ditches; laser level; and control weeds. The field is laser leveled for drainage of 60+ inches of rain as we can not use tile. To close to the water table.
The rows of cane are 6 feet apart. That machine cuts 1 row at a time. It is on tracks because when they start cutting they do not stop rain or shine. Some big plantations even harvest 24/7.
If you look at the machine it has 2 small rollers. 1 on each side. This is to push any pieces of the row next to the one being cut out the way. From there it works the same as ear corn combine. The big rollers stand the cane up and feed it into the machine. That piece stuck out front up high cuts the top off cane as it is mostly leaves. The machine separates the leaves from the cane and the leaves go out the back. It also cuts the cane in pieces about as big as a corn cob. The cane runs up the conveyer to a side dump trailer running along side the harvester.
Like I said if you can picture a 1 row ear corn picker you got the concept of how this machine works.
The side dump trailer being pulled by a tractor goes to a central landing spot where it loads a side dump tractor trailer. They take it to a local mill that crushes the cane and boils down the liquid.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - 12-Volt Conversions for 4-Cylinder Ford 2000 & 4000 Tractors - by Tommy Duvall. After two summers of having to park my old 1964 model 4000 gas 4 cyl. on a hill just in case the 6 volt system, for whatever reason, would not crank her, I decided to try the 12 volt conversion. After some research of convert or not, I decided to go ahead, the main reason being that this tractor was a working tractor, not a show tractor (yet). I did keep everything I replaced for the day I do want to restore her to showroom condition.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.