Posted by super99 on July 08, 2022 at 19:22:19 from (184.20.235.0):
I'm 70 now, when I was a kid, I helped grandad and neighbors in the field as much as school would allow. I spent many hours on M Farmalls, U Minnies, WD AC's and 2 cylinder JD's. I learned how to set a plow from watching older folks do it and then I would be left alone to plow. So many people want to plow now at shows and plow days and don't have a clue how to set up a plow. I watched one young fellow at a plow day years ago. His buddy was pulling a 2 bottom trip plow in cornstalks and stopped to talk. He asked him if he wanted to try it out and the guy said that he had never plowed before, but he would go a round. He got on the tractor and took off, tripped the plow, open the throttle and never looked back until the plow was plugged and riding 2 feet off of the ground. He stopped and pulled the trip lever. Seeing that didn't do any good, he turned the mess around and drove back to the end and said, I'm done and got it his truck and left. The club I belong to has a fall show with corn picking and bean combining and plowing. I've spent a couple of hours each day helping guys get their plows set so they work, some guys get pissy and won't let you help them do a better job. The plowed fields are so uneven that we have to work them crossways several times to get them anywhere near level for next year. The furrows are never straight and when plowing the back lands, instead of tripping out and leaving a 10 or 15 foot wide strip to finish out, they plow right up till the furrows meet and then try to turn on plowed ground and they are a pain to plow in the dead furrows. Just my experiences, how many of you guys can set a plow and how many just hook on and go and never look back?? Chris
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Tractor Profile: Farmall M - by Staff. H so that mountable implements were interchaneable. The Farmall M was most popular with large-acreage row-crop farmers. It was powered by either a high-compression gas engine or a distillate version with lower compression. Options included the Lift-All hydraulic system, a belt pulley, PTO, rubber tires, starter, lights and a swinging drawbar. It could be ordered in the high-crop, wide-front or tricycle configurations. The high-crop version was called a Model MV.
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.