Posted by Geo-TH,In on December 08, 2022 at 04:47:08 from (50.127.118.18):
Yesterday I had too much time on my hands. I found a ballast resistor that may have been used on a Dodge Aspen Mopars first generation electronic ignition. I found a 12v coil. All the used parts are in a drawer dedicated to my Jubilee's parts drawer. So I made a series circuit, a ballast resistor on the left, a HF 10 amp meter going between the ballast and the 12v coil. The circuit is connected to a 12v mower battery which the midtronics meter shows 12.78v. The battery was recently charged. The HF meter on the left is showing a - 4.97v, the ballast voltage. I should have reversed the wires to meter, but who cares. The middle HF meter is reading 3.86 amps. The right HF meter is showing the coil voltage is 6.17v. I ran out of HF meters or I would have measured the volts used by the wires and the ammeter. The wire on the right is a 16g wire. The wire on the left is the hair like wires the 4 amps is going through to the ammeter, the center meter.
Those who are sharp enough will soon ask, where is the missing voltage? Good question. I think part of the problem is meter accuracy, and some of the missing voltage is used by the ammeter and the hair like wires used by the meter.
My objective is to find a used coil and ballast resistor for my Jubilee. My son wants the tractor after I'm gone. He wouldn't have a clue what coil and ballast to buy.
When I have more time to kill. I plan to take the coil off the jubilee and use it in my experiment. If the coil off the Jubilee uses 6v and 4 amps, I would conclude the coils are the same. The coil have a 1.5 ohm primary resistance
If I have 4 amps and 6 volts going to the coil, I'm happy regardless if I have missing voltage.
For all those familiar with Ohm's law. 4 amps and 12v means 3 ohms total is the series circuit. Ballast 1.5 ohms and coil 1.5 ohms = 3 ohms. Does anyone have an ohmmeter that can accurately measure 1.5 ohms plus or minus 1% or 2%? I should ask can anyone afford an ohmmeter that can accurately measure 1.5 ohms plus or minus 1 or 2%?
So much for my round 2 it experiment.
This experiment shows the importance of having accurate and calibrated meters, which obviously I don't have.
I'll let all the EEs answer the questions. I'm sure JohnT and Mark would love to field questions. You-alls have a good day. Is You-alls plural?
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Grain Threshing in the Early 40's - by Jerry D. Coleman. How many of you can sit there and say that you have plowed with a mule? Well I would say not many, but maybe a few. This story is about the day my Grandfather Brown (true name) decided along with my parents to purchase a new Ford tractor. It wasn't really new except to us. The year was about 1967 and my father found a good used Ford 601 tractor to use on the farm instead of "Bob", our old mule. Now my grandfather had had this mule since the mid 40's and he was getting some age on him. S
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.