Posted by timcasbolt on May 27, 2023 at 13:00:51 from (24.112.172.23):
In Reply to: Bolt torque question posted by perryjosh64 on May 27, 2023 at 12:08:12:
Quote: perryjosh64 (quoted from post at 14:08:12 05/27/23) Replacing water pump on a 64 Ford 2000 tractor that started leaking. Figured I d go ahead and replace thermostat and hoses to. While replacing thermostat broke off bolt when I attempted to torque it to 30 ft lb. I assumed this was correct torque as my ford tractor shop manual FO-20 says "tighten the retaining cap screws to a torque of 25-35 ft-lbs" for water pump and both thermostat and water pump bolts are 5/16-18. I thought maybe it broke due to metal fatigue as I used the old bolts. Luckily I was able to get it out with vise grips and went and got new bolt for thermostat and water pump. Thermostat bolts are 5/16-18 1in and water pump are 5/16-18 1-1/4in long and all bolts are grade 5. However everything I find on general torque specs for 5/16-18 grade 5 bolts shows 157-209 in-lb (13-17 ft-lb).
So my question is do I need better grade bolts or is manual wrong for water pump screws torque specs?
I agree that 25-35 is correct for 5/16". Also, grade 5 should be just fine for that application. The old one must have been abused at some point in the past.
This post was edited by timcasbolt on 05/27/2023 at 01:02 pm.
Upload one or more videos to your post. Photo and video filesizes should be less than 8MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Bad Vibes - by Curtis Von Fange. One of the strangest ways to communicate with our tractor is to ask it how it feels. "Ask it how it feels," you say? Yup, ask it how it feels. Now, as with the other articles in this series one has to be able to hear what 'ole blue' is trying to say in response. The nice thing about our old iron friends is that they are usually quite consistent in their response, rather unlike some people I know who might change what they say due to the weather or other mitigating circumstances. But since t
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.