Posted by John T on October 09, 2023 at 06:28:15 from (45.16.200.171):
In Reply to: Outbuilding wire posted by waugh621 on October 08, 2023 at 09:59:55:
Good morning again Nate, as I posted below BEFORE you can size the wire you FIRST have to decide how many Amps of current you will supply to the outbuilding ??
NEXT you have to decide if you want to direct bury multiconductor cable such as UF or USE etc. etc. ORRRRRRRRRRR to use buried conduit with individual conductors such as copper wire type THWN??
NEXT use Aluminum or Copper conductors ??
NEXT compute Line Voltage Drop and if excessive upsize cables
FINALLY consult ampacity charts for the conductors you have chosen TO GET YOUR ANSWER OF WHAT SIZE CABLE IS REQUIRED
NOTE As different types of cable,,,,,, different methods such as direct bury or enclosed in conduit,,,,,,,,different distances,,,,,,,,copper or aluminum conductors,,,,,,,all make a difference, the size you need may or may NOT be the same as someone else used. Of course what someone here used if given the same service requirements ???? might be the same as what you need !!!!!! Your choice take your pick
If you google wire ampacity charts you will get hundreds of hits and below is ONLY ONE SEARCH START so just be aware to consider all the above so you use the correct chart.. I would err on using too large cable versus too small cable myself to allow for upgrades PLUS reduce line voltage drop and while a 60 Amp service may well get you by, Id consider running a 100 Amp service to allow for upgrades.
Compute current requirements, decide on service size, compute distance, compute line voltage drop, decide what type of cable, direct burial or conduit, CONSULT AMPACITY CHARTS that match your chosen cable and method, install a SUB PANEL with separate insulated and isolated Neutral and Ground Buss, provide proper Grounding at sub
Sorry I cant spoon feed you any easy answer not knowing current, distance, type of cable and method selected and wire etc. etc. etc. Where fire and life safety are concerned (do NOT take my word for it) you might want to at least consider consulting the NEC, professional electricians or engineers, or any applicable local authority in addition to the advice offered here (me included)
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - A Lifetime of Farm Machinery - by Joe Michaels. I am a mechanical engineer by profession, specializing in powerplant work. I worked as a machinist and engine erector, with time spent overseas. I have always had a love for machinery, and an appreciation for farming and farm machinery. I was born and raised in Brooklyn, New York. Not a place one would associate with farms or farm machinery. I credit my parents for instilling a lot of good values, a respect for learning, a knowledge of various skills and a little knowledge of farming in me, amo
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.