Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Fly Wheel Start


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bryan in Michigan on March 13, 2002 at 13:54:15 from (216.93.124.242):

In Reply to: Fly Wheel Start posted by Eric on March 13, 2002 at 04:54:59:

Flywheel starting is essentially the same as crank starting. They're both a method of turning over the engine by hand, manually turning the crankshaft. On older John Deeres and other much older tractors with horizontal engines, often two cylinder models which required a larger flywheel (like JD, Hart Parr, Rumely, Eagle, Avery and others), it was a simple matter to use the flywheel for crank starting because it was large enough to grab on to, and it was out in the open. Some had notches cut into the flywheel to fit a lever onto, others have finger depressions cast into them like a steering wheel for grip.

Crank starting I'm sure you're familiar with. The safety rules for crank starting apply to flywheel starting, too. Poor timing, bad stance and grip, or little experience can lead to injury. If the engine kicks back, it can break your hand, wrist or arm. If the crank slips from your grip or comes loose from the tractor incorrectly, then it can go flying through the air, or worse. So, hold on tight, but never wrap your thumb around the handle. Try never to turn the engine more than a quarter turn at a time (it's hard to keep from "spinning" it, but you've got to do it). Always be pulling up on the handle, not pushing down (for a crank, not a flywheel).

If everything's working right, it should be a safe operation. However, the more you do it, the more you increase your risk. I'm about 30 and my dad's about 70. Together, we've been hand-cranking tractors for years (him a bit longer, of course) and we've both had our share of injuries and close calls. But, you gotta love old iron, right?


Follow Ups:




Post A Followup

:
:

: Re: Re: Fly Wheel Start

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Tuning-Up Your Tractor: Plugs & Compression Testing - by Curtis Von Fange. The engine seems to run rough. In the exhaust you can hear an occasion 'poofing' sound like somethings not firing on all cylinders. Under loaded conditions the tractor seems to lack power and it belches black smoke out of the exhaust. For some reason it just doesn't want to start up without cranking and cranking the starter. All these conditions can be signals that your unit is in need of a tune up. Ok, so what is involved in a tune up? You say, swap plugs and file the points....now tha ... [Read Article]

Latest Ad: 1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952 [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy