Tractor Talk Discussion Board |
Re: How big is your shop?
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Chuck, WA on April 16, 2002 at 13:03:25 from (130.20.127.170):
In Reply to: How big is your shop? posted by Dan on April 10, 2002 at 10:15:45:
I wasn't going to respond to this since there are so many varied and excellent replies, but then I thought that perhaps I should reply as maybe representative of "hobby farmers." I suspect that some of what I'm building might not be considered entirely utilitarian, but it will suit me. I know what's said about never being big enough, but I can verify that bigger leads to more stuff, leads to bigger, etc. as somebody already pointed out. Excavation starts in the morning for shop/barn. It is 24 x 36, with a 12 x 36 lean-to on the north side, 12 ft eaves, gambrel roof (21 ft peak) that will let me add a loft, 10 x 16 roll-up door, 4 ft man-door and 3 ft man-door. I'm putting in a drain channel with grate down the center in at least 2/3 of the 36" length for wash-down of whatever, with a drain line into the swale below the barn. Expect to enclose the back 8x24 or 12x24 for a tight, enclosed storage room. Will put shelves along one wall, and workbench along the other, with a 4x6 slider window over the workbench, and a 4x3 slider in each gable. It will be fully insulated, and evantually, I may add a wood or pellet stove for winter. I live in Washington's bananna belt in the Columbia River Basin in Eastern Washington, so don't have the potential for very cold winters - though I do remember the winter of '67 and again in '83 when it got to -24F. I also realize that for some of you folks that's balmy! :) Last winter, it rarely got to single digits, and we had only a couple of days with snow. Under good conditions, I expect to do a lot of work under the lean-to outside. I'll have enough space to get my my MF-35 under cover inside or under the lean-to, to change oil in the truck, or other moderate-size projects. I can ahrdly wait!
Follow Ups:
Home
| Forums
Today's Featured Article -
Good As New - by Bill Goodwin. In the summer of 1995, my father, Russ Goodwin, and I acquired the 1945 Farmall B that my grandfather used as an overseer on a farm in Waynesboro, Georgia. After my grandfather’s death in 1955, J.P. Rollins, son of the landowner, used the tractor. In the winter 1985, while in his possession the engine block cracked and was unrepairable. He had told my father
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|