Tractor Talk Discussion Board |
Re: What does CRP stand for
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Steven@nd on October 06, 2002 at 18:02:03 from (165.234.131.184):
In Reply to: What does CRP stand for posted by Lenny on October 05, 2002 at 17:25:58:
Darn it people, this is out of hand! If anyone would re-read my original post there would be nothing to complain about... Does anyone here remember the dirty 30's?? I doubt it. That happened because people broke up all of the praries to farm and left no grass, no trees, nothing but dirt. Without grass and trees the whole of the earth would wash into the ocean. EROSION is a big problem. EROSION is the reason for CRP. All of the CRP in my area is either a hill that washes away by rain, sand that blows away in the wind, or simply just a alkali mud hole. All of these will be problems if you try to farm them. CRP takes this land out of production and PROTECTS us from having another of the dirty 30's. IF you don't believe me, we have not had rain since spring and it is VERY dry here, but there isn't much dirt blowing because all of the sand was put into grass and that grass is holding the dirt in place. A LOT of this sand that was seeded to grass was a result of the CRP program. The people who have a hobby farm and just use antique equipment or smaller equipment and have a job in town have NO idea how hard it is to be a farmer and rely on that for your sole income. Without CRP this year we would be having an auction sale. Do you people have any idea how it feels to put your heart and soul, blood, sweat, and tears into a crop to watch it dry up in 110 degree heat??? Hobby farmers don't have a clue because there is always a paycheck coming from that job in town. Anyone have a problem with what I said, email me, this board is cluttered up with enough garbage already. If you don't like the government, then change it, you have the right to vote, you also have the right to leave the country too. Steven
Follow Ups:
Home
| Forums
Today's Featured Article -
Talk of the Town: How to Remove a Broken Bolt - by Staff. Another neat discussion from the Tractor Talk Discussion Forum. The discussion started out with the following post: "I have an aluminum steering gear housing with a bolt broken off in it. The bolt is about a 3/8" x 1 1/2" bolt. I've already drilled the center of the bolt out with about 7/64" drill bit the entire length of the bolt. Only one end of the bolt is visible. I tried to use an easy out but it wasn't budging and I didn't want t
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|