Tractor Talk Discussion Board |
Re: Re: Charging a 6 Volt with a 12 volt
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Don LC on January 25, 2003 at 05:51:38 from (24.166.240.210):
In Reply to: Re: Charging a 6 Volt with a 12 volt posted by Bob on January 24, 2003 at 13:50:56:
Go to your local NAPA auto supply store and get,the following parts.... #1 Voltage reducer.-- 12v to 6v(used on early Chrysler cars) #2 length of stranded (red) copper wire,twice as heavy,or a little heaver, as the(red) wire on your 12v charger.This wire should be kept as short as feasable.... #3 clamp, to attach this new wire to the 6v battery post.(red on handle). #4 eylet to connect the new wire to one end of the new voltage reducer.. #5 eylet with no, plastic cover ,so you can clamp the red lead from the 12v charger to the voltage reducer(as large as the reducer has room for(mash the wire connection flat,to give the clamp from the charger a large area to connect too. #6 mount the voltage reducer over the exhaust air grill on the 12v charger....this will help cool the reducer,because it will get hot......make sure the conections at each end of the voltage reducer can not touch the metal mounting ! ! Now, when you need 12v, hook up your charger as usual......if you need 6v, connect the red,(hot)lead from the charger to the tab on the reducer and the new lead from the other end of the reducer will be 6v..... Rember the reducer will cut the voltage in half....so while hooked to 6v the setting on the charger will be putting only 1/2 what the setting is indicating to the battery ---- setting of, 10A your only putting 5A to the battery......it will take twice as long to charge the 6v battery..... I would copy this and take it with you to the store....that way he will know what you are trying to do.....
Follow Ups:
Home
| Forums
Today's Featured Article -
Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|