Tractor Talk Discussion Board |
Re: Praire dogs.
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by John A. on May 23, 2003 at 21:35:09 from (208.24.233.79):
In Reply to: Praire dogs. posted by R.Williams on May 23, 2003 at 13:44:05:
OK Boys, First praire dogs are not pets! They are nuisances, A detrament to land, ruin it for grazing. There mounds can and will cripple a horse if you have to rope sick cattle in that pasture. I know!!! First it is great fun to wile-away a sunday afternoon shooting dogs. After a while they wise up. Even from 300 yds you will miss some so the 1 bullit-1 dead dog won't be the rule. I have seen praire dog towns that gange into the hundreds of acres! So real aggresive measures must be taken to control/eradicate them. Best time to do ground work is after a rain! NH3 (Anhydrous Ammonia) get a trailer that has some in it, Off of the liquid line hose attach a length of pile, stick it down the hole, with a shovel handle, shove some news paper into the hole, cover hole with soil, pack down, crack valve for 30 seconds or so, close valve, pull out pipe,throw extra soil on top of hole and pack down. Go to next hole. After a couple of days you will start seeing results. Go back and retreat any holes that are dug out. Some folks use Drip Gas (condensate collected from natural gas pipe line blow pots) Those of you that have gas lines on your property know what I am talking about. Use the same prosudure as above only subing the drip gas for NH3. There are others who have used pellitized grain fumigant. Use 8 to 10 tablets Same procedure as above. Still others will flood them out with water, then club them to death. The folk I know have NO love for dogs! The last hope one can have for control/eradication is the plauge that hits the praire towns every so often, it can reduce a town by half. If that happens, Then is the time to get after them even harder. For they are weaker and should be easier to kill. Good Hunting, John A.
Follow Ups:
Home
| Forums
Today's Featured Article -
Earthmaster Project Progress Just a little update on my Earthmaster......it's back from the dead! I pulled the head, and soaked the stuck valves with mystery oil overnight, re-installed the head, and bingo, the compression returned. But alas, my carb foiled me again, it would fire a second then flood out. After numerous dead ends for a replacement carb, I went to work fixing mine.I soldered new floats on the float arm, they came from an old motorcycle carb, replaced the packing on the throttle shaft with o-rings, cut new ga
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|