Tractor Talk Discussion Board |
Re: What Do You Think About Going From 6volts To 1
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by RayP(MI) on June 03, 2003 at 16:43:25 from (216.46.197.198):
In Reply to: What Do You Think About Going From 6volts To 12v.? posted by Ron on June 03, 2003 at 09:00:20:
I have two older tractors both converted to 12v. the first I converted was a Farmall 200. I needed new lights, and couldn't find much in 6v - especially those special Farmall sealed beams. By going to 12v, I was able to get sealed beam work lights cheap! Also wanted to put flashing lights, and even a rotating beacon on for safety on the road. Having 12v made these things easy. Alternator was purchased from a backyard rebuilder, cheap! Replaced the coil, old one was questionable anyway. Needed a new battery, so that was a draw. All in all, I've probably got less than $100 in the whole change. Tractor starts very well, can be used to boost anything else on the farm, and I'm happy with the results. Second tractor to get the conversion was a John Deere B. Started very slugishly on 6v, on 12v it's turning over and starting right now! conversion was simple - since generator needed repair anyway, and a new regulator, we just put on a 12v regulator.(And reversed polarity) New battery needed anyway, ignition system is magneto, so nothing needed there, Just a new 12 volt bulbs! Works great. Would never know it is 12v unless looking under the seat. Son refurbished this one for his senior project in high school, and was posted here a while back. Also was pictured in a recent issue of "TWO CYLINDER" magazine. Son was out pulling a field cultivator and grain drill with it last week. To those of you who are purists, and need to keep their 6v systems, I understand. Mine are not show tractors, - they're workers, and I need them to work. I don't scoff at your insistance on 6v systems, please don't look down your nose at me for making practical modifications in my worker tractors.
Follow Ups:
Home
| Forums
Today's Featured Article -
Talk of the Town: How to Remove a Broken Bolt - by Staff. Another neat discussion from the Tractor Talk Discussion Forum. The discussion started out with the following post: "I have an aluminum steering gear housing with a bolt broken off in it. The bolt is about a 3/8" x 1 1/2" bolt. I've already drilled the center of the bolt out with about 7/64" drill bit the entire length of the bolt. Only one end of the bolt is visible. I tried to use an easy out but it wasn't budging and I didn't want t
... [Read Article]
Latest Ad:
2022 John Deere 5045E, 4wd, front end loader and 3rd function with grapple. 120 hrs, 55k new, must sell
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|