Tractor Talk Discussion Board |
Re: GAS TROUBLE
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by txblu on May 28, 2004 at 09:30:13 from (199.46.199.230):
In Reply to: GAS TROUBLE posted by MIKE on May 28, 2004 at 06:32:14:
Fuel Starvation. Your choke only brings fuel to a carb that has no fuel to it. Once the fuel is initially delivered (it fires off) it's the fuel supply system's job is to keep it there, not the chokes. The choke (if working) is forcing your venturi to "suck" more fuel indicating it isn't sucking enough to satisfy the current engine speed. You are indicating that the latter is not happening. It is important to understand that we are addressing a continuous problem of fuel starvation, vs a machine that will run on it's own and then die. The former is fuel air ratio too lean caused by needle valves screwed in too far or obstruction in venturi delivery. The latter would be considered running out of gas which would be a supply problem i.e. fuel inlet port not matching old delivery port, piece of foreign matter in supply line. filter screen plugged up, float misadjusted or operating incorrectly. I think it is too lean a mixture and would start there. You surely have a low speed adjustable jet and could also have a high speed. I'd start with both set to somewhere around 1 to 4 turns open. When seating, do so with your fingers, not a screw driver so as to not damage brass seat. I'd start with the low at 1 1/2 turns open and the high 3 turns open. Then via trial and error optimize the setting. The engine will tell you when you hit the sweet spot. If not come back and talk some more. Good luck Mark
FYI: Quick way to check delivery, is to drop the bottom off the carb, or bowl and allow the float to hang down. Then open the tank supply valve and you should see a pretty good stream of gas running out on the ground (more than a trickle).
Follow Ups:
Home
| Forums
Today's Featured Article -
Grain Threshing in the Early 40's - by Jerry D. Coleman. How many of you can sit there and say that you have plowed with a mule? Well I would say not many, but maybe a few. This story is about the day my Grandfather Brown (true name) decided along with my parents to purchase a new Ford tractor. It wasn't really new except to us. The year was about 1967 and my father found a good used Ford 601 tractor to use on the farm instead of "Bob", our old mule. Now my grandfather had had this mule since the mid 40's and he was getting some age on him. S
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|