Tractor Talk Discussion Board |
Re: new head and gasket seeping already??
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by TheRealRon on August 19, 2004 at 04:51:31 from (69.179.0.225):
In Reply to: Re: new head and gasket seeping already?? posted by Brett Munsey on August 18, 2004 at 20:39:31:
Your are trying to take the lazy man's way out and you risk having to replace a crankshaft... or worse. We told you what you needed to do. If you are not willing to do so, at least take the suggestion to get a local mechanic/machinist to help you. It all has to come apart and everything checked... you have to start at the beginning. You can assume nothing. Just as an example, if the block deck and/or head surfaces are not flat, no amount of gasket sealer nor overtorquing the head bolts will correct the problem. Nor can you assume the gasket does not need sealer because it didn't call for any. You must contact the manufacturer of the gasket and ask. They assume that people who install them know what they are doing. For example, we know that all non-retorque gaskets which are always coated with Teflon, silicone, or graphite, must never have any sealant applied or the gasket is ruined. Conversely, non-embossed metallic gaskets USUALLY require sealant... a nice even coat of Copper-Kote on each side of the gasket (but never sprayed on the deck or head) is appropriate. Composition gaskets (made like a sandwich) are always embossed and MAY require sealer... the manufacturer is the final authority. Hint: when I pull an engine apart, I always look for either sealer on the head bolts or rust on the shank/threads. If any is found, they obviously go through the water jacket. An after-the-fact way to determine this is to carefully blow shop air into each head bolt hole. Use a rubber cone adapter and keep your face out of the way. Air will escape when a hole penetrates the water jacket.
Follow Ups:
Home
| Forums
Today's Featured Article -
Tuning-Up Your Tractor: Plugs & Compression Testing - by Curtis Von Fange. The engine seems to run rough. In the exhaust you can hear an occasion 'poofing' sound like somethings not firing on all cylinders. Under loaded conditions the tractor seems to lack power and it belches black smoke out of the exhaust. For some reason it just doesn't want to start up without cranking and cranking the starter. All these conditions can be signals that your unit is in need of a tune up. Ok, so what is involved in a tune up? You say, swap plugs and file the points....now tha
... [Read Article]
Latest Ad:
1964 I-H 140 tractor with cultivators and sidedresser. Starts and runs good. Asking 2650. CALL RON AT 502-319-1952
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|